The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VI Vx VL moooo ic ww İR a) What is the minimum required coil inductance? b) What is the minimum required capacitor value?

The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VI Vx VL moooo ic ww İR a) What is the minimum required coil inductance? b) What is the minimum required capacitor value?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is:
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
A single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?
what is the schematic diagram of 5v dc-dc tension converter
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain a 24 V output voltage on a 15 ohm load resistor. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. What is the minimum coil inductance and minimum capacitor value?
The inductor current of a buck-boost converter is shown in the figure. The minimum inductor current is zero and the peak value is 5A. The load resistor 5 A value is equal to R=702 Assume that the output voltage ripple is 1%. All components are ideal. Determine. a) Duty ratio. b) Output voltage. c) Input voltage d) Inductor value e) Capacitor value. 12μ 20μ 32μ 40μ t,sec
) A half-wave thyristor converter supplies a purely inductive load, as shown in Figure. If the triggering angle of the thyristor is 120°, the extinction angle will be (a) 240° (b) 180° (c) 200° (d) 120° Vmsinot
A DC-DC buck converter operates in continuous conduction mode. It has 48 V input voltage and it feeds a resistive load of 24 2. The switching frequency of the converter is 250 Hz. If switch-on duration is 1 ms, the load power is
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
Working principle of boost DC TO DC converter
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre