M.a. Which of the following provisions are used to compare ballast quality? A. Bulb size, case material, coil size B. Crest factor, power factor, total harmonic distortion C. Crest factor, filament length, total harmonic distortion D. Bulb size, power factor, case material Mb.The average life of a four-foot-long

Q: Eample 11.6 For the frame shown below, the initial displacement is 25 mm and the initial velocity is…

A:

Q: A tape 30 m long, 0.6 cm wide and 0.5 thick was used to measure a distance of 000 m at a temperature…

A: Given- Measured distance Lm=999.75 mStandard temperature To=20o CField temperature T=35o CActual…

Q: The slope of HGL will be

A: To find : Slope of HGL.

Q: Q2: (A) A cylindrical rod of steel (E-207 GPa) is subjected to load of 11,100 N. If the length of…

A:

Q: (a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the…

A: Double D ring Below shows a Double D ring secured with a Nut and Bolt.

Q: Determine the tensile development lengths required using: (a) ACI Metric Equation 12-1, assuming K,-…

A: Answer We are given fy =350 Mpa f'c = 20 Mpa side cover of bars = 80 mm half of centre to centre…

Q: After fracture, the total length was 53.086 mm and the diameter was 9.982 mm. Plot the engineering…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: An axial flow compressor has a mean radius 0.30m with polytropic efficiency 0.88 receives air…

A: GIVEN- Mean radius=0.30m prototypic efficiency=0.88 axial speed =190m/sec speed(N)=9000rpm Ambient…

Q: 8. What are the reasons for minor head loses in a pipe? a) Friction b) Heat c) Valves and bends d)…

A: Loses in the pipe are classified into two types:  a) Major losses.              Major losses in the…

Q: : - Fluid Department: - Civil Engineering 2nd stage Find the calculation for the experiment 1-…

A: Given:- St=26mm plate in tilt position and plate in perpendicular position To find:- 1- actual force…

Q: During the design of a building the deflection of a beam is calculated to be 0.90 inch. In order to…

A: i = 0.9 in a = 0.75 in

Q: Bar Sample No. deformed deformed Туре Nominal Diameter, mm 1 25 12 12 12 Average Diameter, mm…

A: Given data, Elongation of 2nd bar = 33.25 cm Change in length of 2nd bar = 3.25 cm Change in length…

Q: A liquid which is compressed in a cylinder has a volume of 1 liter at 2Mpa, and a volume of 990…

A: Given data : V1 = 1000 cu.cm , V2 = 990 cu.cm , P1 = 2 Mpa , P2 = 2.5 Mpa Find : Coefficient of…

Q: A rectangular block of dimensior completely submerged in water it found to be 2542.8N. Find; (i) its…

A:

Q: PROBLEM 1: Both a gage and a manometer are attached to a tank to measure pressure. Given the reading…

A: To find height of mercury level

Q: pt 1 Submit y=fax) Ms, Mix 2. (25 pts) A particle is launched from point A with an initial angle of…

A:

Q: A glass capillary tube, 2 mm in diameter, is placed on top of a mercury layer. Calculate the height…

A:

Q: 4. A brass weight is to be attached to the bottom of the cylinder so that the cylinder will be…

A:

Q: answer

A: Force exerted by a jet on a moving plate happens in how many cases? A) 3 cases B) 2 cases C) 1 case…

Q: A plate 0.03 mm distant from a fixed plate, moves at 80 cm/s and requires a force of 4 N per unit…

A:

Q: P = 100 N %3D Hk = 0.30 300 mm 30°/ 200 mm 100 mm B 150 mm FIGURE-ddd Problem-ddd: Consider FIG-ddd…

A:

Q: From the given figure which of the following is/are correct? a. DFAB = DFCB b. FEMAB = FEMBA c. DFBA…

A:

Q: The isosceles triangle gate shown in the figure is hinged at A, and weighs 1500N. Find the location…

A: Consider the following figure:

Q: 4. Calculate the Reynolds Number for 6-inch (diameter) production tubing assuming West Texas Crude…

A: Since; Q1 = 500 STB / day = 5005.434 * 105=9.20*10-4 m3 /s

Q: 2K 8 K 2K 500 lb 90° 30 90° 500 lb 20' B 20' E 20' F 20' Solve for AB

A:

Q: SITUATION. A steel pipe of internal diameter 799 mm and of thickness 2 mm has to be slipped on to a…

A:

Q: 20-mm diameter 0.3 m 0.6 m 60-mm dameter

A:

Q: The system in the figure is supported by a column with a diameter of 50mm. If the modulus of…

A: Modulus of elasticity of the column is 70 GPa or 70000 MPa   Diameter = d = 50mm   L = 1m or 1000mm

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: A compression spring is made of music wire of 2 mm diameter having a shear strength and shear…

A:

Q: Which force measurement device would you prefer to use if your consideration is force changing…

A: Answer is option D Pneumatic Load Cell also operate on the force-balance principle. These devices…

Q: 10. What does FFT in vibration testing stand for? a) Fast Fourier Transformation b) Fast Foil…

A: Introduction- The fast Fourier transform is a method that computes a sequence's fourier Transform…

Q: eigning N each form part of the retaining wall of a swimming pool. 300 540 540 Plastic mm liner…

A: First, check the A and B for both the slide and tip They find the overturning and resisting moment…

Q: na horizontal pipe, which of the following is constant?

A:

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.