mm lL-1000A tape 30 m long, 0.6 cm wide and 0.5 mm thick was used to measure a distance of1000 m at a temperature of 20°C with 120N tension force, mass of tape is 0.7 kg,determine coefficient of thermal expansion of a tape, if:PoStandard tension 50NModulus of elasticity (E) = 210 kN/mm²210x6²Standard temperature 35 °C TSCorrect measured distance = 999.75 m(1000-999.75)=(P-PO) XLAEW²Lгург0125=(120-50) x 30x1²(0.006 x00005) X2-

Given- Measured distance Lm=999.75 mStandard temperature To=20o CField temperature T=35o CActual…

A tape 30 m long, 0.6 cm wide and 0.5 thick was used to measure a distance of 000 m at a temperature of 20°C with 120N tension force, mass of tape is 0.7 kg- determine coefficient of thermal expansion of a tape, if: X=? P-Po) (1000-999.75) = Po Standard tension = 50N Modulus of elasticity (E) = 210 kN/mm² 260x6 Standard temperature 35 °C S Correct measured distance = 999.75 m W²L гург 0125 = (120-5o) x 30x

A tape 30 m long, 0.6 cm wide and 0.5 thick was used to measure a distance of 000 m at a temperature of 20°C with 120N tension force, mass of tape is 0.7 kg- determine coefficient of thermal expansion of a tape, if: X=? P-Po) (1000-999.75) = Po Standard tension = 50N Modulus of elasticity (E) = 210 kN/mm² 260x6 Standard temperature 35 °C S Correct measured distance = 999.75 m W²L гург 0125 = (120-5o) x 30x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2* A thin flat plate is immersed in a fluid stream 20 m/s. Estimate the distance x from the leading edge at which the boundary layer will be I mm or 10 cm for (a) air and (b) water at normal room temperature and pressure. (For air 0.0615 m, 6.47 m; for water 0.044 m, 9.52 m)
A weight, with an unknown mass, falls through a distance of 10 millimeters (mm) onto a collar attached to the bottom end of a vertical bar. The bar is 3 meters (m) long and has a cross-sectional area of 600 square millimeters (mm2). The impact causes the bar to instantly stretch by 2 mm. The Young's modulus of the bar material is 200,000 MPa. Determine: 1. The weight of the falling object. 2. The stress experienced by the bar due to the impact.
Problem 2.1 The Grashof number, Gr is defined as: (where g is gravitational acceleration, B is volumetric thermal expansion coefficient, AT is temperature difference, L is characteristic length, u is the viscosity and v is kinematic viscosity.
A steel tape, with a coefficient of linear expansion of 0.0000116/C, is known to be 100 meters long at 20°C. The tape was used to measure a line was found to be 1532.28 meters long when the temperature was 37°C. Determine the following: Temperature correction per tape length Temperature correction for the measured line Correct length of the line
Question 1 A uniform bar of length L, cross-sectional area A, and mass density p is suspended vertically from one end. (a) Show that the elongation of the bar is & = pgl?/(2E) where g is the gravitational acceleration and E is the modulus of elasticity. (b) If the mass of the bar is M, show that 6 = MgL//2EA)
Please include complete solution and free body diagram.
A plastic rod with length and radius of 300 mm and 30 mm, respectively. If an axial force of 400 N is applied, estimate the length and diameter change. Young’s modulus and Poisson’s ratio of the material are 2.7 Gpa and 0.4 respectively.
Steve Roger measured a line and found it out to be 950 m long using a 20 – m tape under a steady pull of 4 kg at a mean temperature of 25°C. The tape was held in the air and supported at both ends and at the center. Determine the correct length of the line if the tape used is of standard length at 22°C under a pull of 6 kg. Assume the cross-sectional area of tape to be 0.05 cm2, modulus of elasticity as 2.10 x 10^6 kg/cm^2, weighs 0.08 kg/m, and a Coefficient of Thermal Expansion to be 0.0000116/°C.
Show Free Body Diagram Show complete solution anf clear hand writing
A steel rectangular block, a = 2.4cm wide and b = 1.2 cm deep, is subjected to an axial tensile load as shown in the figure. Measurements show the block to increase in length by x=7.11×10-5m (initial length=10cm) and to decrease width by 8 z = 0.533×10-5m, when P is 45 kN. Calculate the modulus of elasticity and Poisson's ratio for the material. P
8. A block of ice float in the sea as shown in the -3 figure below. The density of sea is 1.2 gr cm¯ and density of ice is 0.9 gr c-3. The volume of x ice in sea water = ....... X the volume of ice in the air. Density of sea (Psea) = 1.2 gr -3 cm Gunung es
A 4 meter long steel plate with a rectangular cross section (10 mm x 50 mm) is resting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1x10-5/°C. a. What is the length of shrinkage b. What tension load is needed to return the length to the original value of 4 meters? c. What is the longitudinal strain under this load?