Load 2: A motor draws 22 kW at 0.8 pf lagging. hree loads are connected in parallel across a voltage source of 208 V rms: Load 1: An impedance of 15 + j8 . Load 3: A capacitive load rated at 16 kVA at 0.85, Determine the total complex power, the power factor of the combined load, and the necessary capacitance to correct the power factor of the combined load to unity pf.

Load 2: A motor draws 22 kW at 0.8 pf lagging. hree loads are connected in parallel across a voltage source of 208 V rms: Load 1: An impedance of 15 + j8 . Load 3: A capacitive load rated at 16 kVA at 0.85, Determine the total complex power, the power factor of the combined load, and the necessary capacitance to correct the power factor of the combined load to unity pf.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
2. Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. a) What is the total VA of the combined load? b) What is the overall PF of the combined load? c) What RMS voltage is the combined load operating? d) What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? e) What is its approximate capacitance in microfarad?
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
a- Find the RMS values of the load voltage and the load currentb- Calculate and draw the voltage across the load inductance
S. 20020°V L rms S. In the circuit in the figure; • L1 load draws 15 kVA with lagging power factor 0.6. • The load L 2 draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the reactive power for the load L, ? O 9000 O -3600 O 2700 O 12000 O 4800 O 4500
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Two loads are connected in parallel to a 2000 V(rms) 50Hz source. one of the loads Each of them has 500KVAR reactive power and 0.6 reverse power factor. Other load 300KW since it has absorbing power and 100KVAR dissipating power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) In order for the power factor to be 0.98 back, the capacitor to be connected in parallel with the loads find its value d) The magnitude of the current drawn from the source is measured before and after the capacitor is connected Find and compare for the next cases. Not. Solve this question in detail step by step and explain your requests in detail
Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. What is the total VA of the combined load? What is the overall PF of the combined load? а. b. c. d. What RMS voltage is the combined load operating? What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? е. What is its approximate capacitance in microfarad?