Precision Machining Technology (MindTap Course List)
2nd Edition
ISBN: 9781285444543
Author: Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
List and briefly describe the three types of tolerances used on prints.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
This is a popular solution
Trending nowThis is a popular solution!
Step by stepSolved in 2 steps
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is a dimensioning tolerance?arrow_forwardI need help with number 15. How much would the tolerance be? And where would the Level part go? I've attached the question and my sketch for reference.arrow_forwardI am going to use a Bolt through the .41 DIA holes to align the parts, answer the following:What is the Bolt size (don't worry about the tolerances)?Dim's C=.75, B=2.50, apply a +/-.01 tol to all affected dim's except the .50+/-.03 dim, how far does EDGE D stick out above EDGE E (figure it off the centerline, don't worry abou the clearance between the bolt and the holes)?Min = ? Max= ?arrow_forward
- Would a flatness tolerance of .010 for the part in the drawing below be appropriate? Yes O No 3.000 1.000 XXX = +.005 ANGLES ± 1°arrow_forwardI have three parts that I need answered pertaining to the print provided below. Do the dimensions and tolerances apply before the finish is applied or after? (Multiple Choice)a. beforeb. after In the title block, lower-right corner is a B. Is that the sheet size or the revision status? (Multiple Choice)a. sheet sizeb. revision status What ECN number was assigned to the last revision of this print? What does ECN mostlikely stand for? (Multiple Choice)a. 56003, Engineering change noticeb. 55666, Engineering Coatings notificationc. 65009, Experimental cart noticed. 55666, Engineering change noticearrow_forwarda= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e= 3.0 in. horizontal), Draw the kinematic diagram in SolidWorks drawing sheet with size A3 iso and suitable scale. Solve the following questions and upload the SolidWorks file below. e d. Is the mechanism grashof? Select one: True Falsearrow_forward
- Calculate the tolerance if the maximum limit is 97.45 mm and the minimum limit is 96.99 mm.arrow_forward2. Form tolerances are independent of all other Features O Size Limits Datums O Tolerances ?arrow_forwardSuppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Textarrow_forward
- a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic diagram in SolidWorks drawing sheet with size A3 iso and suitable scale. Solve the following questions and upload the SolidWorks file below. e 'a What is the degree of freedom of the mechanism? а. b. 0 С. 1 d. 4 е. 2.arrow_forward8. A note in the comment section of a title block mentions that all faces should have a +.10 tolerance before heat treatment. The machinist follows the instructions but for diameters he leaves a tolerance of +.20. Why? O A. The machinist may have committed an error, and the part must be returned prior to heat treatment. OB. Diameter dimensions usually change by twice as much as the faces. OC. The tolerances for diameters aren't as critical as face tolerances. D. It's easier for the machinist to adopt MMC for diameters.arrow_forwardI need problems 7, 8, and 9 answered pertaining to the print attached below.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning