Link AC is made of a steel with a 450-MPa ultimate normal stress and has a 6 x 12-mm uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 8-mm diameter pins, while member BCD is connected to its support at B by a 10-mm diameter pin. All the pins are made of steel with a 170-MPa ultimate shear stress and are in single shear. Kwing that a factoaety f32is desired. 12 mm 200 mm It is required to determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes. 150 mm 10

Link AC is made of a steel with a 450-MPa ultimate normal stress and has a 6 x 12-mm uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 8-mm diameter pins, while member BCD is connected to its support at B by a 10-mm diameter pin. All the pins are made of steel with a 170-MPa ultimate shear stress and are in single shear. Kwing that a factoaety f32is desired. 12 mm 200 mm It is required to determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes. 150 mm 10

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.2P

See similar textbooks

Similar questions

The gusset is riveted to a larger plate by 4 – 22mm rivets in single shear arranged andloaded as shown. Calculate the stress in the most heavily loaded rivet.
Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000 lb and F = 3000 lb. 12 in- 6 in 6 in- 13 in F A 13 in B Figure P-912 -12 in- ¯¯Â 2 in 6 in Cross- Section
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. The pipes are attached to rigid supports at A and C, respectively 18 m 14 m Member (a) has a cross-sectional area A,-3,600 mm2, an elastic modul as a cross-sectional area A 3,600 mm2, an elastic modulus E-200 GPa, and an allowable has a cross-sectional area A2 2,o00 mm2, an elastie modulus E-70 GPa, and an allowable normal stress of 120 MPa. Determine the maximum load Pthat can be applied to fange B without exceeding either allowable stress
A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P 20 KN is applied. Shool E-200 GPa A-600mm- L-1 m 2.0 m 0.6 m 1.5 m D. VP-20 KN Aluminum E-70 GPa A-900mm L-1.5 m What is the axial deformation of steel rod in mm?