Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F.

Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.9P: Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For...

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F. Select one: O F=15708N O F= 10472 N O F=5236 N O F= 13090 N O F=6283 N O F=4189 N
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F. Select one: O F=15708 N O F= 5236 N O F= 6283 N O F=4189 N O F= 10472 N O F= 13090N Clear my choice Finish attempt. IOUS ACTIVITY 360 Test - Spring 2020-2021 Jump to. 11:21 PM 4) G ENG 4/15/2021 LEGO ort sc delete end home backspace num lock 7V home enter 4E K pause M
Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 10472 N O F = 6283N O F= 15708 N O F = 4189N O F = 5236 N O F = 13090 N Clear my choice
When a bar of 22 mm diameter is subjected to an axial pull of 60 kN the extension on the 49 mm gauge length is 0.1 mm and there is a decrease in diameter of 0.013 mm. Calculate the Young's Modulus. Provide your answer in GN/m2 to the nearest whole number.
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 3427 N F = 2856 N F = 5712 N F = 8568 N F = 7140 N F = 2285 N
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F. Select one: O F = 5236 N O F = 6283 N %3D O F= 13090N O F = 10472 N O F= 15708N OF=4189 N 9:22 PM EN ? 4/15/2021
Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 2856 N OF = 2285 N OF = 7140N OF = 5712 N OF = 3427 N O F = 8568 N
The force on a wagon wheel is F=2000 N. Find the axle diameter of the wagon wheel made of Fe50 material. Given: GAK=2900 daN/cm2, S=2 F/2 F/2 a=70
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W