lead conductor is 5cm in length and 8 sq. cm in cross-sectional area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of leads is 22x10^-8 Ω-m.

lead conductor is 5cm in length and 8 sq. cm in cross-sectional area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of leads is 22x10^-8 Ω-m.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 1RQ: 1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive...

See similar textbooks

Similar questions

1-343V d) 66-132 kV For a given conductor is AC resistance is 25 Ohm then the DC resistance is Ohm a) 25 b))15.625 c) 40 d) 50
QUESTION 6 What size ungrounded conductors do we need for the 60 amp load? All conductors have typeTHHN insulation. A #6 AWG B #3 AWG C #4 AWG D #1 AWG
A conductor has a resistance of R. it was cut into ten even pieces. Six of them are connected in series, four are connected in parallel. Then they are again connected in series. Find the total resistance. 2.5 6 a M 20. 26 d 3.4 11.25 10
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
What size ungrounded conductors do we need for the 60 amp load? All conductors have typeTHHN insulation. A #6 AWG B #3 AWG C #4 AWG D #1 AWG What size RMC dowe need? A 3" B 3/4" C 1" D 1 1/2"
1. When the length of the conductor is same and the area of cross-section reduced to half then its resistance 2. If you wish to increase the amount of current in a resistor from 240mA to 260mA by changing the 12V source, what should be the new voltage setting be? Answer = 0.05 0.04 0.03. 0.02- 0.01 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 Current 3.The above graph is a showing the relationship between voltage-current. The resistance calculated from the above graph is = 4. Calculate the diameter of a 9.0 cm length of tungsten filament in a small light bulb if its resistance is 0.350. Resistivity of steel is 20 ×10-8 Qm. Answer : = mm Voltage
[Q3] Analyze the following electrical circuit by finding the currents (I1, 12 and 13) using Gauss-elimination method R1 = 50 ohm R3 R2 RI R2 = 25 ohm 12 El = 5 volt R3 = 75 ohm E2 E2 = 4 volt ww
A Certain winding made up of copper has a resistance of 100 2 at room temperature. If resistance temperature coefficient of copper at 0 Co is 0.00428 1/C°. Calculate the winding resistance if temperature is increased to 50 C°. Assume room temperature as 25 C°.
4.-For-labeled currents, draw an arrow to show the direction of the actual positive current. For labeled voltages, circle the node that is at the actual highest potential. Note that the positive and negative signs of the voltage represent the polarity of the probes of a voltmeter connected to the device. The value shown is the reading on the voltmeter. (segment of wire) 2A -2A -5A 2.de 3A TA Cov E 5V 12V + 3V -10V -201
The resistance of a conductor with uniform length is defined by O All are correct O R= |/oS O R= (P)/S O R= V/i
Q.2 A B 7.5 cm 12 ст 7.5 cm 12 cm 7.5 ст b a An iron block is shown in the figure with two different perspectives. Find the resistance if a voltage is applied (a) between A and B, and (b) between C and D. (resistivity of iron: = 9.71x10-8 ohm. m)
Solve 2,3 only.Note the load resistance is 10 ohm and frequency 60 Hz