yields under a load of 8KN; it attains a max load of 15KN and breaks finallyA tensile test is carried out on a bar of mild steel of diameter 20mm. The barЕxampleat a load of 7KN.EstimateyP(i) The tensile stress at the yield point(ii) The ultimate tensile testii. Max loa(iii) The average stress at the breaking point if the diameter of neck isOmm.

Part A) Write the equation for tensile stress at the yield point as follows.

lameter 20mm. The bar A tensile test is carried out on a bar of mild yields under a load of 8KN; it attains a max load of 15KN and breaks finally at a load of 7KN. Estimate i) The tensile stress at the yield point i) The ultimate tensile test ii) The average stress at the breaking point if the diameter of neck is mm.

lameter 20mm. The bar A tensile test is carried out on a bar of mild yields under a load of 8KN; it attains a max load of 15KN and breaks finally at a load of 7KN. Estimate i) The tensile stress at the yield point i) The ultimate tensile test ii) The average stress at the breaking point if the diameter of neck is mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please answer i) and ii)
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 61 % - Percentage of Reduction in Area = 43 % - Final length after fracture = 34.8 mm - Final Diameter after fracture = 4.2 mm & - Ultimate stress = 433 MPa Determine the Initial length, Initial diameter and Maximum load. SOLUTION: i) Initial Length (in mm) = Answer for part 1 ii) Final Area (in mm2) = Answer for part 2 iii) Initial Area (in mm2) = Answer for part 3 iv) Initial Diameter (in mm) = Answer for part 4 v) Ultimate Load (in N) = Answer for part 5
What is the tensile strength of the bar if the yield stress is equal to 275MPa?
A soft steel specimen has a BHN of 150, find the equivalent 29 tensile strength in MPa. A. 393 B. 503 C. 443 D. 533 What is the value of strain at yield point of 1-inch diameter C1030 as rolled steel in the stress-strain curve? A. 0.0012 B. 0.0015 C. 0.0017 D. 0.0022 A copper column of annular cross section has an outer diameter of 0.5 m. and is subjected to an axial loading of 5 kips. The allowable compressive stress is 2 ksi. Compute the wall thickness. A. 1.15 m B. 2m C. 0.8 m D. 1 m
Typically, the shear yield stress is what fraction of the tensile yield stress? Select one: a. 0.002 O b. 0.5 O c. 0.8 O d. 0.02 O e. 0.1
39)A tensile test specimen has a gage length=3.0 inches and a diameter= .75 inches. Yielding occurs at a load of 38000lbs. The corresponding gage length=3.0103 inches (neglect the .0.2% yield point). The maximum load of 54000lbs is reached at a gage length =3.453 inches. If fracture occurs at a gage length of 3.873inches, determine the percent elongation at fracture (Round to the nearest whole %)
During a tensile test on a specimen of 100mm^2 cross-section, maximum load observed was 71168N and area of cross-section at neck was 50mm^2. Ultimate tensile strength of the specimen is?
10. A standard steel specimen of 0.504" diameter elongated 0.0125" in an 8" gage length during a test where it was subjected to a tensile force of 6249 lb. If the specimen's gage length was measured to be 8.0025" after the test was over, what was the permanent plastic deformation? What is the elastic deformation and what is the modulus of elasticity of that metal? r PL AE
In the state of loading as made of brittle material tensile and compression fracture values of the exposed arm, respectively. σUT=200 MPa and σUC=800 MPa and factor of safety n=4 as it is; a) First reduce the applied forces to point B, b) By determining the critical point of the critical section and stresses Calculate it and show it on the stress element. c) Calculate the diameter of the AB part according to the Coulomb criterion. Note: Neglect the effect of cutting forces.
The results of a tensile test are: Diameter of the specimen Gauge length Load at limit of Proportionality Extension at the limit of Proportionality Maximum Load : 10mm :40 mm :80kN : 0.06mm. :100 kN Calculate ultimate tensile stress and young's modulus.
The total load for a canopy overhang is 105,340# and the load is equally distributed to five steel rod ties. The sample steel rod tested has tensile strength of 20,000psi. A selection of steel rods (same material as the tested sample) is available in different sizes shown below. Select the rod size that best fits this application? (SA = Surface Area) (f= P/A) (LO4) O 1" (SA= 0.79 sq in) 3/4" (SA=0.44 sq in) O½" (SA= 0.20 sq in) O 1¼" (SA= 1.22 sq in) O 1½ (SA= 1.76 sq in)
2-9 Discussions What are the differences between the oy, ou and E determined from tensile and compression tests? 1. 2. Do you agree that the tensile and compression tests for the same material have the same results? Explain.