The total load for a canopy overhang is 105,340# and the load is equally distributed to five steelrod ties. The sample steel rod tested has tensile strength of 20,000psi. A selection of steel rods(same material as the tested sample) is available in different sizes shown below. Select the rodsize that best fits this application? (SA = Surface Area) (f= P/A) (LO4)O 1" (SA= 0.79 sq in)3/4" (SA=0.44 sq in)O½" (SA= 0.20 sq in)O 1¼" (SA= 1.22 sq in)O 1½ (SA= 1.76 sq in)

Answered: Image /qna-images/answer/e19dfaf8-df08-4179-942a-d76af267b1f8.jpg

Answered: The total load for a canopy overhang is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 51 mm diameter steel rod (E = 207 GPA) with pinned end conditions is to be subjected to an axail compressive load. What is maximum length in mm (1 decimal place) for it to be considered a short column?
show complete solution and show the necessary diagrams needed
Use F.S. 2 against buckling. (Figure 1) Figure 4 ft 1 of 1 D 3 ft Part A It P=20 kip, determine the required minimum diameter of the A392 steel sold sind BD Express your answer to three significant figures and include the appropriate unit d=2.5 B μA
Uuestion 1: Calculate the axial load of spiral column with respect to first and second peaks. Materials used are C25 and S420 for longitudinal bars of 8- 024 and for spirals. Use the design strength of concrete and steel. 2. A, fywk 0, = D (s) 4. Ao P. = D (s) fa = f+4.0-0, GAP fa 4. f ynk (A min p, = 0.45. , min p, = 0.12. ywk D=550 mm H=600 mm Spiral : 010/85 mm 200 mm
Please answer with full steps and drawings please
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
Required information Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Given: P₁ = 65 kN and P2 = 40 kN. Take Es = 200 GPa and Eb = 105 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -180- Dimensions in mum Steel B 120- P₁ 40-mm diam. 100 100 DI C Brass 30-mm diam. Determine the reactions at A and E. The reaction at A is The reaction at Eis P2 E KN (Click to select) ✓ KN (Click to select)
suppose the free length is 65 mm. Find the stress at solidity in units of MPa Circle final answer
On the arm made of steel, a) Stresses at the critical point of the critical section show it on the element by calculating. b) Maximum shear stress (Tresca) criterion whether the diameter d is safe using check (σY = 280 MPa and n = 2). (Shear force effect will be neglected.)
The unit of torsional rigidity and the flexural rigidity is the same. Select one: True False
Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as shown. Take di = 30 mm, d2 = 50 mm, and P = 85 KN. 0.9 m 125 AN 125 IN 12 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is | MPa.
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa or 82,000 psi respectively.what is required diameter? Take factor of safety is 2.3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS