LAD 2: 000 001 -LEQ Less Than or Eql Source Source B N7:7 0 360 0168h What value must be in N7:6 for output O:2/4 to be turned ON? O 15 or less 14 or less 359 or less O 240 or greater -MUL Multiply Source Source B Dest N7:6 0 24 0018h N7:7 0 0:2/4 X

Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e

QUESTION 1 Find out the rounded integer output (in decimal format) of a10 bit A/D converter for the following two cases? Assume that the input to ADC in both cases is 500mV. Also, assume that the ADC uses a 15V supply voltage. The converter input range is 0 to 10V. Case 1: Reference voltage: 10V. Case 2: Reference Voltage: 5V.   A 26 and 51   B 52 and 103   C 104 and 206   D 26 and 206 In Question 1, If a choice is given, which reference voltage you would pick?   A. 5V   B. 10V   C. 20V   D. All choices give same results In Question 1, What is the ADC output value (in decimal format) for the input of 7V for the case of reference voltage = 5V? Answer: 1023 Answers are highlighted. Work Step-by-Step solution to get the answer.

VI Ru Ri Vz I, R2 Io R2 = 3837.79 Q. R1 = 3763.67 0. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. %3D V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo

wit Determine Ssketch the output voltage mave form? 1MF- pvi/v 200KR Viown 80807 -4

Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage V 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Icc 6.2 Total, Output HIGH mA Total, Output LOW 9.8 74 74 74 2.7 -20

Question 8 160 Which of the po160100555- 870479447 In the DAC unit, the analog level at the A 1601005559870479447 g160100555 B 0870479447 There may be applications that require digital-to-analog conversion but do not need analog-to-digital conversion. 9870479447 1601008 9441 Basically, the process is the reverse of the conversion) changed and in this 160 0555 - 987 9441 The signal produced by this conversion process can basically be 555-987 s respect it is similar то 916 It would not be possible to produce a realistic sine signal with a 4-bit DAC unit. 087047944 to the PWM unit. 1601008 160100555 measured with a DC multimeter. 2555-987047944 g160100555 - 7944 9168

i just want a paragraph of these sensors and their function and which is best then the other.PZT-5HPZT-5JModif. PZT-5A

In the operation of a half-wave rectifier with a capacitor-input filter, the ripple factor can be lowered by the value of the filter capacitor or + the load resistors.

3. For the half-wave rectifier given in the figure below, find the average values of the output voltage and current, and the ripple factor of the output voltage. D1 Io Dbreak R1 1k vo VAMPL = 169.71 FREQ = 50