Q8 XBb Take Test: Program Control Instru X +board.com/webapps/assessment/take/launch.jsp?course_assessment_id=_132181_1&course_id=_11224_1&content_id= 12Question Completion Status:THE TOTCHIon of the rau round the is to determine now the processor responds to a power ranure.TrueO FalseQUESTION 8L1oInputsS10-S2S30-S40-S5QUESTION 91234Ladder logic programS1PL3()HE36S3JES5JES21010(IMPPL1()PL4S45 [LBL]]()PL2OutputsPL1PL2PL3 X¤PL4-L2Assume all switches are turned off after each operation.Referencing the above program, When Switch S2 is turned on first, then switch S5 is turned on. Output PL4 be energizedO TrueO False

Given a ladder logic. To find will the output PL4 be energized when switch S2 is turned on first,…

L1 Inputs o-S1 o-S2 0-S3 o-S4 0-S5 2 S3 3 3E 4 Ladder logic program S1 HE 5 S5 3E 10 LBL S2 36 S4 PL3 () 10 (JMP) PL1 PL4 o PL2 Outputs PL1 PL2 PL3 PL4 ¤ L2 Assume all switches are turned off after each operation. Referencing the above program, When Switch S2 is turned on first, then switch S5 is turned on. Output PL4 be energize O True False

L1 Inputs o-S1 o-S2 0-S3 o-S4 0-S5 2 S3 3 3E 4 Ladder logic program S1 HE 5 S5 3E 10 LBL S2 36 S4 PL3 () 10 (JMP) PL1 PL4 o PL2 Outputs PL1 PL2 PL3 PL4 ¤ L2 Assume all switches are turned off after each operation. Referencing the above program, When Switch S2 is turned on first, then switch S5 is turned on. Output PL4 be energize O True False

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

How does TP4056 works? What is the purpose of red and blue lights in the components?
Given the model for position control system, find the value for K1 and K2 so that the peak time is equal to 0.5s and the %OS is equal to 3%.
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
Describe what is meant by sequence control.
I need a complete experience about Dispersion Compensation technique for the optical fiber communication using a program Optisystem
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
The OCC is measured by increasing the fieldcurrent in steps from zero to some maximum value, and recording the corresponding values of armature emf. If now the current is decreased from maximum to zero, the emf values will be different; why?
With the aid of power-load angle curves explain in details i) An electronic governor’s response to frequency changes resulting from changing loads.
What is fusing factor ?
A dc shunt moton runs at looo Y.P.m From 500V SUPPIY when taking an armatuie currant of 95 A . caleulat e the spees at which itwill Ynn ffom 9250v supPly when taking an armature eurrent of 50A. the resis tance of the armature circuit o. .ssume the flud Per Pole at 250V to have decreased to 70%% of its Value qt 500 V ·
Test the accuracy of the equation by applying the operation in Ampere law (del.)? If there is a mistake, correct this mistake.