Refrigerant vapor rejects 70 kW ofheat as it passes through an air-cooled condenser. The condenser hasan air-side area of 210 m2 and basedon this area, has an overall heattransfer coefficient of 0.037kW/m2.°C. Cooling air flows at a rateof 7.59 kg/s. If condensation of therefrigerant occurs at 55°C, what is theoutlet temperature (in °C) of the air?Take the specific heat of air to be 1.02kJ/kg.°C.

To determine the final temperature of the air through the condenser, we must use the concept of heat…

Answered: ketrigerant vapor reje neat as it…

ketrigerant vapor reje neat as it passes through an air- cooled condenser. The condenser has an air-side area of 210 m2 and based on this area, has an overall heat cransfer coefficient of 0.037

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The clean U for an exchanger is 800 BTU/(hr 0 F ft2). Its tube area is 600 ft2. After operating for several months heating water from 50 0F to 160 0F at a flow rate of 210 GPM with a heating fluid on the shell entering at 290 0F and exiting at 160 0 F has the overall U decreased significantly?
Calculate the mean condensing heat – transfer coefficient when refrigerant 12 condenses on the outside of the horizontal tubes in a shell – and – tube condenser. The outside diameter of the tubes is 19 mm, and in the vertical rows of tubes there are, respectively, two, three, four, three and two tubes. The refrigerant is condensing at a temperature of 52°C, and the temperature of the tubes is 44°C. Please refer for the table below.
What is the formula of modulus of elasticity. Write it's unit.
An ammonia system with a 158-kW evaporator operating at -1°C and a 35-kW evaporator operatingat -40°C uses flash gas removal and intercooling. The condensing temperature is 32°C. Thearrangement is as shown. How many kilograms per minute of ammonia are compressed by the high-pressure compressor?
An ice plant of 200 tons refrigeration capacity makes use of the shelland tube superheat remover. The temperature of discharge is 112 OCand vapor is cooled to 52 OC. Water enters at 24 OC and is heatedduring the counterflow with the vapor to 70 OC. The compressoroperates at 1352.2 kPaa condenser pressure and 247.14 kPaaevaporating pressure. The overall coefficient of heat transfer is 390kJ/hr-m2-C. Calculate the LMTD.
Pls answer with complete solution.
A freon 12 waste water system operating at 5 °C suction temperature and a 40°C condensing temperature has an evaporator load 17.6 KW. If the condenser is selected for a 70°C water temperature rises, how many gpm must be circulated through the condenser? The following enthalpies have been found; condenser entrance =377 kJ/kg; exitA=238.5 kJ/kg; evaporator entrance =238.5 kJ/kg; exit = 253.6 kJ/kg.
helpp
The condenser of a steam power plant has a total surface area of 45m^2 and an overall heat transfer coefficient of 2100Watts/m^2-K. Saturated steam from the turbine enters this condenser at 30C and leaves as saturated liquid at the same temperature. Cooling water enters the condenser at 14C and leaves at 22C. A. Draw the figure, sketch the t-L diagram, then, compute the LMTD of the cross-flow heat exchanger in Kelvin. B. How much heat is transferred by the condenser in MW? C. How much steam passes through the condenser in kg/s? D. How much cooling water is supplied to the condenser in kg/s.
. A 10 TR ammonia ice plant has a two-pass shell-and-tube water-cooled condenser. The water enters at 30°C. The temperature rise of water may be taken as 2.5°C. The refrigerant condensing temperature is 35°C, the heat rejection ratio of the plant is 1.35. The condenser has 24 steel tubes of 21 mm OD and 13.65 mm ID. Determine the length of the tubes.
Problem: An ammonia refrigerating system shown in the figure is composed of three evaporators and arranged with multiple expansion valves and intercoolers. The load and operating temperature of each evaporator are shown in the table below: condenser evaporator 3 compressor 3 intercooler 2 evaporator 2 compressor 2 Infercooler 2 liquid evaporator 1 compressor 1 Evaporator Load, tons Evaporator Temperature, °C 1 30 - 30 20 - 20 15 - 10 Condensing pressure is 1200 kPa. Refrigerant vapor exits evaporator no. 1 with a 10 - degree superheat. Saturated conditions exist at the exits of the evaporator no. 2 and evaporator no. 3. Liquid refrigerant leaves the condenser at 28°C. Determine a. the mass flow rate in evaporator 1 kg/s b. the mass flow rate in evaporator 2 kg/s c. the mass flow rate in evaporator 3 kg/s
A straight-condensing 10,000 kW turbine has a guaranteed steam rate of 5.90 kg/kW.hr when exhausting at 5.0 kPa. Exhaust steam enters the condenser at 92% quality, and it is estimated that fouling will decrease the overall coefficient by 30% during operation. Cooling water is available at 18 ℃, and for design purposes, 1 ½ in OD 16 BWG Brass tubes (thickness = 0.065 in, k=62 BTU/hrftF°.) are specified with 9 C° rise in cooling water, which circulates at 5 ft/s. Inside and outside film coefficients are hi=960 and ho=1474 BTU/hrft2F°. Design a condenser for this turbine, considering tube and boundary resistance as flat surfaces and neglecting any crossflow factor. Determine the followinga) Effective overall coefficient of heat transferb) Volume flow rate of cooling waterc) Number of tubes for single passd) Length of tubes