k= 50N/m M A 3 30° B 600 N

Q: If the mass of the flowerpot is 65 kg, calculate the tension generated in every cable for…

A:

Q: Q: Body A weights 80 lb and body B weight 100 lb and they are connected by cable and equilibrium.…

A: Given:mass of Body A(mA)=80 lbmass of body B (mB)=100 lbα+β+120°=180°α+β=60°To find :- α and β

Q: 6 m 3m 4 m 4 m 4 m 6 m 3 m m 4 m

A: Write coordinates of A,B,C and DA=0,0,3.5B=3,4,4C=-6,-3,6D=4,-3,4

Q: Q4: Determine the zero members and state weather of the members in tension or compression |10KN F C…

A:

Q: Cable AB is 0.5 m long. The unextended length of the spring is 0.4 m. When the 50-kg mass is…

A: The given data are: L=0.5 mm=50 kgΔx=0.45 m-0.4 m=0.05 m Here, L denotes the length, m denotes the…

Q: The uniform 15-m pole has a mass of 150 kg and is supported by its smooth ends against the vertical…

A: Given:m=150 KgL=15 m

Q: The springs in are shown in the equilibrium position. 3m 3 m KAC = 20 N/m KAB = 30 N/m wwwww KAD-40…

A:

Q: For the shown frame LDetermine the reactions at Pin A and atB 2What is the force developing in Cable…

A:

Q: Q2/ Determine the unstretched length of spring AC if a force P = 80lb cause the angle 0 = 60 for…

A: Solution:

Q: find the reaction at both support

A:

Q: Q- Two radial 200 N and 500 N forces and tangential 700 N force are applied to shown system. If the…

A: Draw a labeled free-body diagram of the given system. Calculate angle Ɵ, θ=sin-11.1 m2 m=33.37°…

Q: Draw the Free-Body Diagram if the weight acts on point G

A:

Q: Determine the tension developed in each cable for equilibrium of the 300-lb crate. CG 3 ft 6 ft 3 ft…

A:

Q: The body is in equilibrium when the resultant of the force acting * .on dose not zero true False O

A: A body will always be in equilibrium if the sum of forces acting on it zero or body is remain at…

Q: The wall-mounted 3kg light fixture has its mass centre at G. Determine the vector reactions at A.…

A:

Q: 3. Determine the force P needed to hold the 100-kg block in equilibrium.

A:

Q: If the mass of cylinder A is 41 kg, determine the tension in cable (DE) in order to hold the…

A:

Q: determine the tension in all three cables if the bouyancy force on the balloon is 1035 N, the mass…

A: According to the given data F→=1035 j N W→=-87.7x9.81 j=-860.337 j Co-ordinates of the point…

Q: determine the magnitude of the resultant force ( in SI Unit ) acting on the bracket and its F;= 300…

A: Given, ϕ=400F1=150 N Let the force F2 makes an angle α with the horizontal Therefore sinα=35cosα=45…

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: Determine the magnitude of the reaction in the pin A, the cable BC and the cable that supports the…

A: Given Data To find1) Ay1 Ax2) T

Q: Determine the tension in cable AC. The bucket has a mass of 60 kilograms.

A:

Q: Determine the tension in each cable necessary for equilibrium of the massless pipe supporting 800…

A: Uniform load applied on pipe:Total length of the uniform load:And structure is symmetric about XZ…

Q: Knowing that F = 370 N and 0 = 15°, determine the tension in the spring and reactions at A if the…

A: The force F=370 NLength of the arm AD=400 mm=0.4 mLength of the arm AB=300 mm=0.3 mAngle between the…

Q: Q4. Determine the support reaction on the member. The collar at A is fixed to the member and can…

A:

Q: Determine the tensions T₁ and T₂ in the strings required to maintain equilibrium for the suspended…

A:

Q: Aroller of weight 500 N has a radius of 120 mm and is pulled over a step of height 60 mm by a…

A:

Q: Determine the tension developed in wires CA and CB required for cquilibrium of the 10-kg cylinder.…

A: Find the tension force in each member.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.