Jennifer is a Mechanical Engineer, and is hired to design a massive 450 MW power plant for the city of Dubai. Jennifer decides that the optimal efficiency would be obtained if the pressure of saturated vapor entering the turbine should be 10 MPa, and the pressure of saturated liquid exiting the condenser to be 0.005 MPa.  Dubai is in the United Arab Emirates (UAE), where the water from the Persian Gulf is 40 °C and UAE environmental laws limit the exiting cooling water to a maximum temperature of 45 °C (in order to prevent damage to the local fishing industry).  For Jennifer’s power plant, calculate:   heat input form the boiler (in Mega Watts) thermal efficiency mass flow rate of cooling water (in kg/s)

Q: b) Consider a steady, incompressible, parallel, laminar flow of a film of oil falling slowly down a…

A: given; (i) state all assumption you require to simplify the above to a one-dimensional flow problem.…

Q: (a)the pressure at which reheating takes place, (b)the total rate of heat input in the boiler, and…

A:

Q: A bag of wheat weight 290 kg .To what height should it be raised so that potential energy is 7680 J?…

A: Introduction : In this question we are provided with value of potential energy , acceleration due to…

Q: An Actual Rankine Engine receives steam at 10 MPa and 350C. The steam expands adiabatically to a…

A: Given dataEngine inlet temperature = T1  = 350°CEngine inlet pressure = P1 = 10 MPa = 100 barAfter…

Q: Magnetic tape tape is in conta tangential com the total accel CCE

A: an of P1=37m/s2at of P2=43m/s2r1=117mm=0.117mr2=58mm=0.058m   To-Find:- v=a1=a2=

Q: boat is to be tested at 1:20 sc 2.5 m/s in fresh water at 10 approximate distance from the insition…

A:

Q: In a once-through boiler, feed water enters through the bottom of tubes, receives heat from…

A: Given data-pressure of feed water at turbine=22.0 MpaTf=523KSuper heated steem pressure…

Q: When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical…

A:

Q: P7. Water is the working fluid in an ideal Rankine cycle. The saturated vapor enters the turbine at…

A: Answer: (a) The net work per unit mass of steam flowing is 923.6288 kJ/kg. (b) The heat transfer to…

Q: The winding drum D is drawing in the cable at an accelerated rate of 4.5 m/s^2. Determine the cable…

A: Given            Mass, M = 1000 kg Acceleration, a = 4.5 m/s2 Find   Tension in the cable, T

Q: Cars A and B travel in the same direction in two adjacent highway lanes. At t=0, car B is a distance…

A:

Q: Example 2 Two spheres are pressed against each other by an external force. The diameter of the…

A: Poisson's RatioWhen a piece of elastic is in its unique shape which is a cuboid and is pulled along…

Q: Given a rankine cycle with reheat operating with the following conditions: Boiler Exit Conditions:…

A: Given that: Mass flow rate of the steam→m˙=7 Kg/s Now from the steam table: At 10.11 MPa:…

Q: QUESTION 2 Condenser Diagram 2E shows an ideal cascade vapour-compression refrigeration cycle using…

A: Given: m1˙=11160 kg/hour=3.1 kg/sP1=100 kPaP2=P3=280 kPaP6=P7=900 kPa To find 1. Coefficient of…

Q: The performance data of a water pump follow the curve fit Havailable =Ho +aV², where the head…

A: Havailable=Ho+αV2.............equation…

Q: A 4in ductile iron pipe carries 0.20 ft3/s of glycerin (SG=1.26) at 100°F. Is the flow laminar or…

A: Diameter of pipe, d=4 in =412ftVolume flow rate glicerin, Q=0.20 ft3/sSpecific gravity of glycerin,…

Q: in Figure Q1(b). The two plates move in opposite directions with constant velocities V, and V2.…

A:

Q: Task 4): you are required to design a PID controller f for the Chassis, what model derive and what…

A:

Q: What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3°…

A:

Q: Draw the complete shearing force and bending moment diagram for the beam shown in the figure. Draw…

A:

Q: The rod OA rotates counterclockwise with a constant angular velocity of 0 = 5 rad/s. Two…

A:

Q: Find the theoretical volume of air at 20 deg. C and 100 kPaa to burn 1kg of coal C = 65.65% O =…

A: Soln In a given question we have :- C= 65.5% Mass of C= 656.5 hm O= 18.61 % Mass of O = 186.1 gm{…

Q: D, the smallest pipe for

A: GIVEN- Re= 2300 Q= 1L/s TO FIND- Smallest pipe (D)

Q: A pump is used to raise water from open tank to another one. If the pipe diameter is 300 mm, Length…

A:

Q: A 22-lb body is traveling in a horizontal straight line with a velocity of 11.1 ft/sec when a…

A:

Q: Evaporative condenser is used only air as condensing medium to condense the hot vapour refrigerant.…

A: The given statement is false.

Q: Find the Transfer Function G(s)= X3(s) / F(s) for each network shown in figure N°5 c

A: The transfer function for the following mechanical translation system is calculated below:

Q: The evaporator is device used in the high pressure side of a refrigeration system. * O True False

A: The given statement is false.

Q: Shift weight A so the lever would balance at 7/8 of the total length of the board measured from left…

A:

Q: Mr Hafiz is required to create a survey on his subordinate opinion on cost and standard of living.…

A: Inferential Statistics (for instance, a diagram or chart) and inferential insights permits you to…

Q: The pressure of refrigerant at the inlet compressor is called; * suction pressure discharge pressure…

A:

Q: explain the two phase component diagram of Cu-Ni and apply the phase rule

A: given; explain the two phase component diagram of Cu-Ni and apply the phase rule

Q: A fluid flow is given by : V = 10x'i – 8x'yj. Find the shear strain rate and state whether the flow…

A: V= 10x3i- 8x3yj

Q: Read the questions carefully before answering.  Box  or  indicate  your  final answers  when…

A:

Q: operate with an initial pressure of 1.69356 Mpa and 370.356oC temperature and exhaust to a heating…

A:

Q: In the course of Material Mechanics, you may study that for the bar under tensile loading, the…

A:

Q: 1. The velocity of a car is given by v(f) = 60(1– (0.7)*), where v is measured in m/s and t is…

A:

Q: A Newtonian fluid flows in an annular space created by a concentric pipe of radius R. and a rod of…

A:

Q: A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt…

A: (1) Calculate the bolt length. l=ta+tc Here, l is the grip length, ta is the thickness of the…

Q: A = C5 x 9 B = W8 x 21 find the Moment of Inertia Ix about neutral axis X-X (in⁴), and the Iy…

A: Moment of inertia is characterized as the amount communicated by the body opposing rakish speed…

Q: simple Rankine cycles operate with an initial pressure of 1.69546 Mpa and 370.546oC temperature and…

A: Since you have asked a multi-part question which contains more than three sub-parts. Thus, according…

Q: list down the derivation of formulas and describe each variable of "Impulse and Momentum" (Dynamics…

A:

Q: A boron implant at 30 keV is done through a gate oxide that is 15nm thick, into a silicon substrate.…

A: Solution: Given Data: Rp=1000 Ao∆Lp=250 Ao

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: 1. A controlling torque , in gravity controlled instruments. is attached to the moving system in…

A: Correct answer: Small weight Note: We know that, small weight is attached to the moving system in…

Q: Turbine (HP) Re-heat Turbine (LP) PH P1 Diagram 1H A co-generating Rankine cycle is shown in Diagram…

A: Given: Boiler Pressure 4 MPa Condenser Pressure=18 kPa process heater pressure =2 MPa Reheater…

Q: 1. A 500-lb block is in contact with a 45 deg incline. The coefficient of static friction is 0.25.…

A:

Q: Draw shearing stress distribution of the critical section? 500kN 12mm 12mm 276mm 12mm 150mm

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: A major water main is an 18 in ductile iron pipe. Compute the Reynolds Number if the pipe carries…

A: given  data; diameter of pipe(d)=18in                            =0.4572mdischarge from…

Q: 28. Find the transfer function, G(s) = X1(s)/ F(s), for the translational mechanical system shown in…

A: