Item 2 The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 3 MPa. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 160 MPa and 256 MPa, respectively. The tank has an inner diameter of 4 m. Figure 1 of 1 Determine the required minimum thickness of the cylindrical shell. (Figure 1) Express your answer with the appropriate units. te = 37.5 mm Submit Correct My Answers Give Up Part B Determine the required minimum thickness of the hemispherical shell. Express your answer with the appropriate units. t₂ = 18.8 mm

Item 2 The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 3 MPa. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 160 MPa and 256 MPa, respectively. The tank has an inner diameter of 4 m. Figure 1 of 1 Determine the required minimum thickness of the cylindrical shell. (Figure 1) Express your answer with the appropriate units. te = 37.5 mm Submit Correct My Answers Give Up Part B Determine the required minimum thickness of the hemispherical shell. Express your answer with the appropriate units. t₂ = 18.8 mm

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.34P: using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of...

See similar textbooks

Similar questions

47 H.WOA rod Consists of three bars af unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rood ?_use E= 200GPA %3D =30mm =20 mm 1.5m 2.5m 2m
5 of 21 What is the internal yield pressure (psi) of 3.5 inch, H-40, 7.7 Ib/ft external upset tubing? 4320 psi 3610 psi 4630 psi None of the above
A storage tank if fabricated by bolting together two half cylindrical shells as shown. The tank is designed to withstand a pressure of 3MPa. The tank and the 25mm bolts are made from a material having an allowable normal stress of 158MPa and 246MPa respectively. The tank's inner diameter is 4m. What are the required thickness of the hemispherical and cylindrical shells and the required number of bolts in each hemispherical cap?
The gas storage tank is fabricated in the following manner: a 10-mm thick plate is rolled to form a cylindrical shell which is bolted on one side, then its ends are sealed by bolting two hemispherical shells. The resulting inner diameter of the tank is 4 m. All bolts have a diameter of 15 mm. If the internal pressure in the tank is 1 MPa, determine the following:a. the number of bolts needed in each hemispherical shell if the normal stress in the bolts should not exceed 250 MPab. the minimum required thickness of the hemispherical shells if the normal stress in the shell should not exceed 125 MPac. the hoop stress in the cylinderd. the minimum require spacing of the bolts in the cylindrical shell if the normal stress in the bolts should not exceed 250 MPa.
If the gauge is made of a material having a yield stress equal 200 MPa, determine the minimum required diameter d. Using a factor of safety (F.S. = 2) -50 mm–
QUIZ 11. In ammunition testing center the pressure is found to be 255 MPa. Calculate the changein volume of the piece of the copper piece when subjected to this pressure inpercentage. The bulk modulus of copper is 1.38 x Pa.2. Two liters of water, when subjected to a pressure of 10 atm, are compressed by 1.013cc. Find the compressibility of the water. Note: Compressibility = 1/K.3. A solid rubber ball has its volume reduced by 14.5% when subjected to uniform stress of1.45 x 10 4 N/m 2 . Find the bulk modulus for rubber.4. The capillary rise when a glass capillary tube of diameter 0.4mm is dipped vertically inolive oil is 3.8mm. If the angle of contact of olive oil with glass is 0 deg and the density ofolive oil is 920 kg/cu.m, find the surface tension of olive oil.5. A liquid rises to a height of 9cm in a glass capillary of radius 0.02 cm. What will be theheight of the liquid column in a similar glass capillary of radius 0.03 cm?
Calculate the critical load for the column. Pcr = ______kips
130 N A 30 mm C Determine also: a) Force at A b) Force at B c) Force at C В D -40 mm- -60 mm Analytical solution, two digits behind comma.
Calculate for the degree of indeterminancy.If nth degree, input nIf unstable, input -1If determinate, input -2
6) A hollow steel tube is to be used to carry an axial compressive load of 160 kN. The yield stress for steel is 250 N/mm2. A factor of safety of 1.75 is to be used in the design. The following three class of tubes of external diameter 101.6 mm are available. Class Thickness Light Medium 4.05 mm 3.65 mm Heavy 4.85 mm Which section do you recommend?
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
H.W.2: A hollow steel [E = diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). The bar is loaded as shown in Figure 30,000ksi] tube (1) with an outside %3D Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial assembly. 34 kips 18 kips 25 kips (2) (3) (1) Sho B. 18 kips 34 kips 40 in. 30 in. 60 in. FIGURE