It is made of a fiber core with an index of refraction of 1.8 and a coating with an index of refraction of 1.7 of a 2km long optical fiber cable in the air environment. Determine the acceptance angle 0, and the maximum usable data rate of signals that can be transmitted over the fiber. a = 16.25°, fp = 0.2Mb. s-¹ 0a 16.25°, fp = 6.1Mb.s¹ 9a-46.7°, fp = 1.6Mb.s¹ a = -25.18°, fp = 4.3Mb. s¹ Ba= 36.27°, fp = 0.7Mb.s¹

It is made of a fiber core with an index of refraction of 1.8 and a coating with an index of refraction of 1.7 of a 2km long optical fiber cable in the air environment. Determine the acceptance angle 0, and the maximum usable data rate of signals that can be transmitted over the fiber. a = 16.25°, fp = 0.2Mb. s-¹ 0a 16.25°, fp = 6.1Mb.s¹ 9a-46.7°, fp = 1.6Mb.s¹ a = -25.18°, fp = 4.3Mb. s¹ Ba= 36.27°, fp = 0.7Mb.s¹

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 4 to separate ITU channel 59 using a fiber Bragg grating (FBG) and an optical circulator. The FBG is made from a fiber with an effective index of refraction of the core of 1.48 at You are to implement a simple one-channel demultiplexer ITU channel 59. a.) Draw a diagram of the demultiplexer b.) Calculate the periodicity of the index of refraction modulation in the core of the FBG fiber
Determine the cutoff wavelength for a step-index fiber to exhibit single-mode operation when the core refractive index is 1.46 and the core radius is 4.5 um, with the relative index difference of 0.25 %.
Q. (a)Two nicols are first crossed and then one of them is rotated through 600. Calculate the percentage of incident light transmitted. Q. (b)Two nicols are oriented with their principal plane making an angle of 600.What percentage of incident unpolarized light will pass through the system? Q.The signal retrieved in an optical fiber reduces at its output to one-tenth of its input power. What is the overall attenuation? What shall be the power at output in a fiber having loss3 db/km?
What is a waveguide? What is a slab waveguide? What is a planar waveguide? What is thin slab?
3) Solve the cutoff frequency for the first mode and third mode of WR137 waveguide. TABLE 7.1 Some Standard Rectangular Waveguides Waveguide designation a (in) b (in) t (in) Seo (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12-1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2-12.4 WR62 0.622 0.311 0.040 9.49 12.4-18
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
A single mode fibre is to be dimensioned. The normalised frequency is 80 % of the maximum allowed for single mode condition. The relative refractive index difference is 0.005 and the refractive index of the core is 1.5. The wavelength is 1.5 µm. A. Determine the radius of the core. B. If the number of modes supported by this fiber is 5. Determine the radius of the core.
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface.
Internal critical angle in core at core-cladding interface of a step index fiber is 78.6°. Determine the maximum acceptance angle if the refractive index of cladding is 1.45. Also determine numerical aperture and fractional index difference.
Find the VSWR, if the reflection coefficient is 0.8
(a) A 1 MHz carrier with an amplitude of 1V is modulated by a 1 kHz signal with m=0.5. Sketch the voltage spectrum. (b) An additional 2 kHz signal modulates the carrier with m=0.2. Sketch the new spectrum.
A standard waveguide WR187, has the following dimensions: outside walls 2.000 x 1.000 in., wall thickness 0.064 in. Determine the highest frequency that can be transmitted if only the TE10 mode is permitted. What modes can exist in it if it is excited by a wave of frequency 6.00 GHz?