Internet Check sum Consider the figure below (simplex communication scenario). The TCP sendel sends an initial window of 4 segments. Suppose the initial value of the sender )) sequence number, SEQ1, is 100 and the first 4-segments each contain 400 bytes of payload. As you can see ACK 3 is lost. What is the SEQ number (SEQ2, SEQ3, SEQ4, SEQ5) from the Sender and ACK Number (ACK1, ACK2, ACK3, ACK4, ACK5) from the receiver for each segment? Sender Seq1 Seq2- Seq3 Seg4 ACK1 ACK2 X ACK3 ACK4 Seq5 ACK5 Receiver

Internet Check sum Consider the figure below (simplex communication scenario). The TCP sendel sends an initial window of 4 segments. Suppose the initial value of the sender )) sequence number, SEQ1, is 100 and the first 4-segments each contain 400 bytes of payload. As you can see ACK 3 is lost. What is the SEQ number (SEQ2, SEQ3, SEQ4, SEQ5) from the Sender and ACK Number (ACK1, ACK2, ACK3, ACK4, ACK5) from the receiver for each segment? Sender Seq1 Seq2- Seq3 Seg4 ACK1 ACK2 X ACK3 ACK4 Seq5 ACK5 Receiver

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 10VE

See similar textbooks

Similar questions

Consider the figure below in which a TCP sender and receiver communicate over a connection in which the sender->receiver segments may be lost. The TCP sender sends an initial window of 5 segments. Suppose the initial value of the sender->receiver sequence number is 362 and the first 5 segments each contain 638 bytes. The delay between the sender and receiver is 7 time units, and so the first segment arrives at the receiver at t=8. As shown in the figure below, 3 of the 5 segment(s) are lost between the segment and receiver.
Consider TCP client with ISN = 20120 communicating with a TCP server with ISN = 30130 -client has 4500 data bytes to send to the server -client MSS = 1500 bytes -server has 6000 data bytes to send back -server MSS = 3000 bytes -show all the client-server transactions to transfer all data in both directions (sequence numbers, ack numbers for all arrows).
Write a code in C that prints the following: Prints default TCP send and receive buffer sizes.Prints default UDP send and receive buffer sizes.Prints default SCTP send and receive buffer sizes.
In a TCP data packet, if the sequence number has the value 001111, ACK number has the value 010110 and the urgent pointer has the value 001100 assuming that URG flag is set. What is the last urgent byte in the data section of the packet? All numbers are in binary.
. If size of a TCP segment is 1KB and header length value is 6, the sequence number = 3500. Given that URG flag = 1 and URG pointer = 45. Then what is the total size of data. How many of them are urgent, Give the sequence numbers of urgent data.
Consider the following scenario in which host A is sending a file to host B over a TCP connection. Assuming that the sequence number of the first data byte sent by A is 0 and every segment always includes 1000 bytes of data, excluding the TCP header. At some point of time, bytes up to 6400 have been written into the sender’s buffer. Bytes up to 4999 have been sent out but the segment which contains bytes 2000~2999 has not arrived at host B yet. At the receiver’s side, all bytes up to 3999 have been received except for bytes 2000~2999. Bytes up to 499 have been read from the buffer by the application. Assume that the maximum size of the sender’s buffer is large enough. Consider the sliding window algorithm in TCP and answer the following questions. 1) What are the values for LastByteAcked, LastByteSent, and LastByteWritten? 2) What are the values for LastByteRead, NextByteExpected, and LastByteRcvd? 3) Assuming that the maximum size of the receiver’s buffer is 4000 byte, what would…
In TCP Fast Retransmit, if we receive three duplicate ACKS after sending out a packet that is not incrementally ACK-ed but before the time-out associated with that packet, we immediately retransmit the packet without waiting for the timeout to occur. Why do we wait for three duplicates instead of just one?
Computer Science Write TCP Send/Receive methods for text-based communication which uses the “$>!!$>” as the boundary pattern for messages. You can use Helper classes to ease your pseudo code.
Consider the figure below in which a TCP sender and receiver communicate over a connection in which the segments can be lost. The TCP sender wants to send a total of 10 segments to the receiver and sends an initial window of 5 segments at t = 1, 2, 3, 4, and 5, respectively. Suppose the initial value of the sequence number is 151 and every segment sent to the receiver each contains 612 bytes. The delay between the sender and receiver is 7 time units, and so the first segment arrives at the receiver at t = 8, and an ACK for this segment arrives at t = 15. As shown in the figure, 1 of the 5 segments is lost between the sender and the receiver, but none of the ACKs are lost. Assume there are no timeouts and any out of order segments received are thrown out.
(ESP) Consider that we protect a TCP SYN packet using the ESP in the transport mode. A TCP SYN packet just comprises a TCP header which is 20 bytes (i.e., without TCP option). The IP packet header is also 20 bytes long (i.e., without IP option). Moreover, the block size for encryption is 256 bits (e.g., using AES-256), and the hash output’s size for message authentication is 512 bits (e.g., using SHA-1). What is the minimum amount of padding required?
A TCP connection is using a window size of 8,000 bytes and the previousacknowledgment number was 10,001. It receives a segment with acknowledgment number 12,001 and window size advertisement of 7,000 bytes. Draw a diagram to show the situation of the window before and after.
The following is a dump of UDP header in hexadecimal format 5EFA00FD001C3297 What is the total length of user datagram? Is the packet from client to server or vice versa?