ing is proportional to the current in that winding because (a) Ohm's law applies to magnetic circuits (b) leakage paths do not saturate (c) the two windings are electrically isolated (d) mutual flux is confined to the core. In a two-winding transformer, the e.m.f.per turn in secondary winding is always........the induced e.m.f. power turn in primary. (a) equal to K times (b) equal to 1/K times (c) equal to (d) greater than. In relation to a transformer, the ratio 20: 1 indi- cates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one

ing is proportional to the current in that winding because (a) Ohm's law applies to magnetic circuits (b) leakage paths do not saturate (c) the two windings are electrically isolated (d) mutual flux is confined to the core. In a two-winding transformer, the e.m.f.per turn in secondary winding is always........the induced e.m.f. power turn in primary. (a) equal to K times (b) equal to 1/K times (c) equal to (d) greater than. In relation to a transformer, the ratio 20: 1 indi- cates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9P

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
A small single-phase 60 Hz transformer has 10.2 W at no load. The core has a volume of 750 cm3. The maximum flux density is 10,000 G and the hysteresis constant of the core is 0.0005. Using the Steinmetz law on hysteresis loss, find the eddy current loss.
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
The amount of inrush current in the primary of a transformer is limited by the........, A- amount of applied voltage, B- resistance of the wire in the primary winding, C- flux change of the magnetic field in the core, D - all of the above What precaution must be observed when working whit current transformers? A- never have a load on the secondary, B- always ha a load on the secondary, C- de-energize the primary whenever there is a load on the secondary, D - none The fact that the movable coil of a constant-current transformer moves further away from the stationary coil with a increase in load current is based on which fundamental priciple of magnetism? A- like magnetic poles attract, B- like magnetic poles repel, C- the amount of current flowing through a coil inverdely proportional to its flux density. D- none