Homework Help is Here – Start Your Trial Now!
Engineering
Mechanical Engineering
Industry Print Exercise 7-1 Refer to the print PR 7-1 and answer the questions below. 1. For this print, is SECTION A-A an auxiliary view? 2. Notice the view that features the circular view of the hole through this part. Not counting Detail A, how many auxiliary views are projected from that view? 3. Are there any center lines shown in the auxiliary views? 4. If the lower-left auxiliary view is considered a depth auxiliary, which value shown in the view is a depth dimension, the .63 measurement or the .57 measurement? 5. In the view identified as SECTION A-A, how many depth dimensions are given? 6. Detail A is an enlarged partial view. Is it considered to be an auxiliary view also? Review questions based on previous units: 7. What is the drawing/part number? 8. What is the name of this part? 9. Is there a cutting-plane line on this drawing?__ 10. Is the view located in the lower-left area of the drawing a section view? 11. At what scale is the enlarged Detail A? 12. On what size paper was the original drawing created? 13. Do the visible lines of this drawing appear to be two times thicker than the other lines? 14. As you visualize this part, does it have any holes in it? 15. In this drawing, the material is specified outside of the title block as a note. In inches, how thick is the material used to make this part?

Industry Print Exercise 7-1 Refer to the print PR 7-1 and answer the questions below. 1. For this print, is SECTION A-A an auxiliary view? 2. Notice the view that features the circular view of the hole through this part. Not counting Detail A, how many auxiliary views are projected from that view? 3. Are there any center lines shown in the auxiliary views? 4. If the lower-left auxiliary view is considered a depth auxiliary, which value shown in the view is a depth dimension, the .63 measurement or the .57 measurement? 5. In the view identified as SECTION A-A, how many depth dimensions are given? 6. Detail A is an enlarged partial view. Is it considered to be an auxiliary view also? Review questions based on previous units: 7. What is the drawing/part number? 8. What is the name of this part? 9. Is there a cutting-plane line on this drawing?__ 10. Is the view located in the lower-left area of the drawing a section view? 11. At what scale is the enlarged Detail A? 12. On what size paper was the original drawing created? 13. Do the visible lines of this drawing appear to be two times thicker than the other lines? 14. As you visualize this part, does it have any holes in it? 15. In this drawing, the material is specified outside of the title block as a note. In inches, how thick is the material used to make this part?

Elements Of Electromagnetics
Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
See similar textbooks
icon
Related questions
Question

I need help answering these questions, please.

Industry Print Exercise 7-1 Refer to the print PR 7-1 and answer the questions below. 1. For this print, is SECTION A-A an auxiliary view? 2. Notice the view that features the circular view of the hole through this part. Not counting Detail A, how many auxiliary views are projected from that view? 3. Are there any center lines shown in the auxiliary views? 4. If the lower-left auxiliary view is considered a depth auxiliary, which value shown in the view is a depth dimension, the .63 measurement or the .57 measurement? 5. In the view identified as SECTION A-A, how many depth dimensions are given? 6. Detail A is an enlarged partial view. Is it considered to be an auxiliary view also?_ Review questions based on previous units: 7. What is the drawing/part number? 8. What is the name of this part? 9. Is there a cutting-plane line on this drawing? 10. Is the view located in the lower-left area of the drawing a section view? 11. At what scale is the enlarged Detail A? 12. On what size paper was the original drawing created? 13. Do the visible lines of this drawing appear to be two times thicker than the other lines? 14. As you visualize this part, does it have any holes in it?_ 15. In this drawing, the material is specified outside of the title block as a note. In inches, how thick is the material used to make this part?
Transcribed Image Text:Industry Print Exercise 7-1 Refer to the print PR 7-1 and answer the questions below. 1. For this print, is SECTION A-A an auxiliary view? 2. Notice the view that features the circular view of the hole through this part. Not counting Detail A, how many auxiliary views are projected from that view? 3. Are there any center lines shown in the auxiliary views? 4. If the lower-left auxiliary view is considered a depth auxiliary, which value shown in the view is a depth dimension, the .63 measurement or the .57 measurement? 5. In the view identified as SECTION A-A, how many depth dimensions are given? 6. Detail A is an enlarged partial view. Is it considered to be an auxiliary view also?_ Review questions based on previous units: 7. What is the drawing/part number? 8. What is the name of this part? 9. Is there a cutting-plane line on this drawing? 10. Is the view located in the lower-left area of the drawing a section view? 11. At what scale is the enlarged Detail A? 12. On what size paper was the original drawing created? 13. Do the visible lines of this drawing appear to be two times thicker than the other lines? 14. As you visualize this part, does it have any holes in it?_ 15. In this drawing, the material is specified outside of the title block as a note. In inches, how thick is the material used to make this part?
.83 .78 2X SHAVE- THIS AREA -DETAIL A X 3X R.11 SECTION A-A SCALE 1:1 2X 120* 110 32 .63*.0422 801 797 R1,680 R1.320 1.500 R1,866 2X R.250 2X R.125 2X R.100222 2.13 315 38 1.07 NOTES: 1. UNLESS OTHERWISE SPECIFIED AREAS INDICATED TO BE FREE OF BURRS, 50% MIN SHAVED SURFACE. 2X 21 o .750 3. MATERIAL: 950XF OR A607 GRADE 50 -12 GAGE (.105 THICK) O 3X R.500 A MATERIAL: 3 020 X Y Z ,007 .903 Hydro-Gear FINISHE YELLOW ZINC DIOROMATE X .1126 .0966 .020 60. 40° .04 .02 040 XYZ DETAIL A SCALE 4:1 DATE DRAIN 10/01 NAME 1-DEAS TOLERANCES UNLESS SPECIFIED 8.070 PROJECT REFERENCE: EZT 4.000 SIZE SCALE NAME ARM, NEUTRAL LEFT C FULL E CHANCES FORMER PART NO. SHEET 1 OF 1 PART NO. 52195 OG
Transcribed Image Text:.83 .78 2X SHAVE- THIS AREA -DETAIL A X 3X R.11 SECTION A-A SCALE 1:1 2X 120* 110 32 .63*.0422 801 797 R1,680 R1.320 1.500 R1,866 2X R.250 2X R.125 2X R.100222 2.13 315 38 1.07 NOTES: 1. UNLESS OTHERWISE SPECIFIED AREAS INDICATED TO BE FREE OF BURRS, 50% MIN SHAVED SURFACE. 2X 21 o .750 3. MATERIAL: 950XF OR A607 GRADE 50 -12 GAGE (.105 THICK) O 3X R.500 A MATERIAL: 3 020 X Y Z ,007 .903 Hydro-Gear FINISHE YELLOW ZINC DIOROMATE X .1126 .0966 .020 60. 40° .04 .02 040 XYZ DETAIL A SCALE 4:1 DATE DRAIN 10/01 NAME 1-DEAS TOLERANCES UNLESS SPECIFIED 8.070 PROJECT REFERENCE: EZT 4.000 SIZE SCALE NAME ARM, NEUTRAL LEFT C FULL E CHANCES FORMER PART NO. SHEET 1 OF 1 PART NO. 52195 OG
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Knowledge Booster
Elastic Constants and Their Relationship
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Elements Of Electromagnetics
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Control Systems Engineering
Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY
Mechanics of Materials (MindTap Course List)
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Engineering Mechanics: Statics
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY
SEE MORE TEXTBOOKS