Incremental fuel cost in Rs/MWh for a plant consisting two generating units G₁ and G₂ is dC₁ dP₁ = 0.12 P₁ + 120 dC₂ dP₂ = 0.25 P₂ + 200 Where, P₁ and P2 are the generation in MW of G₁ and G₂ respectively. If system is operating at economic dispatch with P1 = P2 = 180 MW and 0.3 where, PL is dP. SP₂ the transmission loss, then the penalty factor of G₁ will be

Incremental fuel cost in Rs/MWh for a plant consisting two generating units G₁ and G₂ is dC₁ dP₁ = 0.12 P₁ + 120 dC₂ dP₂ = 0.25 P₂ + 200 Where, P₁ and P2 are the generation in MW of G₁ and G₂ respectively. If system is operating at economic dispatch with P1 = P2 = 180 MW and 0.3 where, PL is dP. SP₂ the transmission loss, then the penalty factor of G₁ will be

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.32MCQ: While the instantaneous electric power delivered by a single-phase generator under balanced...

See similar textbooks

Similar questions

2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
Q5 A single area consists of two generating units, rated at 400 MVA and 800 MVA, with speed regulation of 4 % and 5 % on their respective ratings. The units are operating in parallel, sharing 700 MW. Unit 1 supplies 200 MW and unit 2 supplies 500 MW at 60 Hz. The load is increased by 130 MW. The load varies 0.804 % for every 1 % change in frequency. Find the steady state frequency deviation and the new generation on each unit. Select base 1000MVA.
Turbine operating efficiency is not influence to maintain the minimum cost of power generation True False
A 50 Hz synchronous generator having inertia constant H = 5 sec and a direct axis reactance X, = 0.3 p.u. is connected to an infinite bus through a transformer and a double circuit line. The network is purely reactive. The synchronous generator is delivering real power P power Q = 0.074 p.u. to the infinite bus of 1.0 p.u at steady state. 0.8 p.u. and reactive %3D 70.2 X = J0.3 E's Voo = 120° X = 0.3 X = J0.3
Problem 3.1: Determine the rms value of voltage induced in an 80-turn coil on a 30 cm × 25 cm cross-section core with peak flux density 1.7 T alternat- ing at 60 Hz. Problem 3.2: Two parallel 1-phase rectangular bus bars 2 cm apart at their cen- ter lines experience 30,000 A,ms current when a load gets short-circuited. Determine the peak mechanical force per meter length of the bus bars. Assume the bus bar shape factor K = 0.85.
Suppose two generators supplying a load. Generator-1 has a no-load frequency of 61.5 Hz and a slopesp1 of 1 MW/Hz. Generator-2 has a no-load frequency of 62 Hz and a slope sp2 of 1MW/Hz. The twogenerators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. Draw the resulting systempower-frequency or house-diagrams. Determine (a) at what frequency is the system operating, andhow much power is supplied by each of the generators? (b) if an additional 0.75-MW load wereattached to this power system. What would the new system frequency be, and how much powerwould the each generator supply now? (c) with the system in the configuration described in part (b),what will the system frequency and generators power be if the governor set points on generator-1 areincreased by 0.5 Hz?
Discuss about generator modeling and drive the formula for the real and reactive power supply it .
For a power station the yearly load duration curve is a straight line from 40,000 to 3000 kw. To meet the load three turbo-generators are installed. The capacity of two generators is 15,000 kw each and the 3d is rated at 6,000 kw. Determine the following a) Load factor. b) Capacity factor. c) Maximum demand.
As seen in the figure, three generators of 800 kW, 900 kW and 1000 kW are connected in parallel. It generators feed 380 kW load. Frequency-active power graphs of generators are shown as given. According to this; a. Calculate the operating frequency for the situation given in the question.b. Calculate the power transferred by the generators to the load.c. A three-phase asynchronous load of 800 kW and 600 kVA with a reverse power coefficient of 0.78 is installed in the system. engine is connected. The new operating frequency of the system and the active power of the alternators. calculate.d. Do you think the generators in this system are suitable for parallel connection as in the figure?
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle & (b) Reictive power drawn by the load Carry out calculations in pu form and convert the result to actual values.
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
What are FACTS (Flexible Alternating Current Transmission Systems), and how do they enhance power system performance and control?