b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (i) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.

b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (i) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Similar questions

two generators supplying a load. Generator I has a no-load frequency of 62.5 Hz and a slope Sp1 of I MW/Hz. Generator 2 has a no-load frequency of 62.0 Hz and a slope sp2 of I MW/Hz. The two generators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. (a) At what frequency is this system operating, and how much power is supplied by each of the two generators? (b) Suppose an additional I-MW load were attached to this power system. What would the new system frequency be, and how much power would Gl and G2 supply now? Generator 1 VT V2 Generator 2 VTí KVAR KVAR
Suppose two generators supplying a load. Generator-1 has a no-load frequency of 61.5 Hz and a slopesp1 of 1 MW/Hz. Generator-2 has a no-load frequency of 62 Hz and a slope sp2 of 1MW/Hz. The twogenerators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. Draw the resulting systempower-frequency or house-diagrams. Determine (a) at what frequency is the system operating, andhow much power is supplied by each of the generators? (b) if an additional 0.75-MW load wereattached to this power system. What would the new system frequency be, and how much powerwould the each generator supply now? (c) with the system in the configuration described in part (b),what will the system frequency and generators power be if the governor set points on generator-1 areincreased by 0.5 Hz?
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 20 MVA, 50 Hz, 0.85 PF lagging, 4-poles, Y-connected, with a synchronous reactance of 2 N and an armature resistance of 0.05 Q. Each of generators Gj and G2 has a characteristic power-frequency slope of 4.7 MW/Hz, while generator G3 has a slope of 5.0 MW/Hz. If all three generators are supplying a total load of 51.2 MW, and the no-load frequency of each generator is set to 52.4 Hz, what will the system frequency be? How much power is supplied by generator G3? Select one: O a. fsys = 48.84 Hz, PG3 =17.8 MW O b. fsys = 49.05 Hz, PG3 = 16.75 MW c. fsys = 48.95 Hz, PG3 = 17.25 MW d. None
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 20 MVA, 50 Hz, 0.85 PF lagging, 4-poles, Y-connected, with a synchronous reactance of 2 Q and an armature resistance of 0.05 Q. Each of generators G1 and G2 has a characteristic power-frequency slope of 4.7 MW/Hz, while generator G3 has a slope of 5.0 MW/Hz. If all three generators are supplying a total load of 51.2 MW, and the no-load frequency of each generator is set to 52.4 Hz, what will the system frequency be? How much power is supplied by generator G3? Select one: O a. fsys = 48.84 Hz, PG3 = 17.8 MW O b. None O c. fsys = 49.05 Hz, PG3 = 16.75 MW O d. fsys = 48.95 Hz, PG3 = 17.25 MW Clear my choice
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 20 MVA, 50 Hz, 0.85 PF lagging, 4-poles, Y-connected, with a synchronous reactance of 2 Q and an armature resistance of 0.05 N. Each of generators G1 and G2 has a characteristic power-frequency slope of 4.7 MW/Hz, while generator G3 has a slope of 5.0 MW/Hz. If all three generators are supplying a total load of 51.2 MW, and the no-load frequency of each generator is set to 52.4 Hz, what will the system frequency be? How much power is supplied by generator G3? Select one: O a. fsys = 48.84 Hz, PG3 = 17.8 MW O b. fsys = 49.05 Hz, PG3 = 16.75 MW O c. fsys = 48.95 Hz, PG3 = 17.25 MW O d. None
two synchronous generators are connected in parallel, feeding a load together. the frequency of the first generator in the no-load State is 52 Hz and the slope of the characteristic is 1 MW/Hz. the total power of the load fed by these two generators is 2.5 MW and the power coefficient is 0.6 inductive. by drawing the characteristic curve of the system;a) what is the frequency of the system when the load in question is fed, and how do the two generators share the load between themselvesb) if a load of 0.5 MW is added to the system, find the operating frequency of the new system and the powers given by each generatorc) if a second load of 0.5 MW is connected to the system, the idle operating frequency of the second generator is increased by 0.5 Hz, what happens to the operating frequency of the system and the power values given by the generators
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 24 MVA, 50 Hz, 0.85 PF lagging, 4-poles, Y-connected, with synchronous reactance of 2 Q and an armature resistance of 0.05 Q. Each of generators G1 , G2 , and G3 has a characteristic power-frequency slope of 4.2 MW/Hz , 4.5 MW/Hz, and 5.0 MW/Hz, respectively The no-load frequency of each generator is set to 52.4 Hz. The load increases with no changes in the settings of the no-load frequencies, until a generator reaches its maximum rated power first. At what system frequency does this limit occur? Select one: O a. fsys = 49.2 Hz O b. None O c. fsys = 48.9 Hz O d. fsys = 48.32 Hz Clear my choice
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 25.4 MVA, 60 Hz, 0.77 PF lagging, 4-poles, Y-connected, with synchronous reactance of 2 Q and an armature resistance of 0.05 Q. Each of generators G1 , and G2 has a characteristic power-frequency slope of 5.8 MW/Hz, and no-load frequency of 62.5 Hz. Generator G3 has a characteristic power-frequency slope of 6.0 MW/Hz. Find the no-load frequency of generator G3 for which all generators supply a load of 42.6 MW, at fsys = 60 Hz. Select one: O a. fevs = 62.95 Hz O b. fsys = 62.26 Hz O c. None O d. fsys = 62.5 Hz
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 21 MVA, 50 Hz, 0.85 PF lagging, 4-poles, Y-connected, with synchronous reactance of 2 Q and an armature resistance of 0.05 Q. Each of generators G1 , G2, and G3 has a characteristic power-frequency slope of 5.2 MW/Hz , 4.5 MW/Hz, and 4.9 MW/Hz, respectively The no-load frequency of each generator is set to 52.4 Hz. The load increases with no changes in the settings of the no-load frequencies, until a generator reaches its maximum rated power first. At what system frequency does this limit occur? Select one: O a. fsys = 48.97 Hz O b. fsys = 48.25 Hz c. fsys = 49.22 Hz O d. None
Two generators are supplying a load. Both the generators have a no-load frequency of61.5 Hz and the slope sp of 1 MW/HZ. If they are supplying a real load of 2.0 MW at 0.8 pflagging, what would be the system frequency and power sharing between two generators?What measures can be taken to make the frequency 60 HZ. If an additional 1.0 MW load isconnected to the existing one what would the system frequency be.
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle & (b) Reictive power drawn by the load Carry out calculations in pu form and convert the result to actual values.