in. R 0.505 in. dia. 2 in. FIGURE P1-54 Tensile test specimen for Problem 1-54. 3/8

Q: Q // If the value of the highest load we get from the tensile test of a wrought iron model with a…

A:

Q: In the BrinelI hardness test, if the load used 1200 kg, and the ball diameter 6 mm, write down the…

A:

Q: Segments AB and CD of the assembly are solid circular rods. A) What is the normal stress in segment…

A:

Q: A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from…

A: Given: The allowable compressive stress = 5.2 Mpa The inclination of plane = 30 degree The shear…

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

A:

Q: 1) The steel tube in the system below has an outside radius as listed and an inside diameter of…

A:

Q: Problem 1-3 The Cartesian components of stresses at a point are given as belou : O = 7, 0y = 6, oz =…

A: The cartesian components of stresses at a position specified in the inquiry are known to us :…

Q: An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have…

A: The objective of the question is to determine the critical point of the system, apply Mohr's circle…

Q: If a 10" tall stainless steel rod with diameter of %" is receiving 20K lbs tensile load, how much…

A:

Q: The steel bar has the dimensions shown. (Figure 1) Figure 30 mm 24 mm 20 mm o k 60 mm - 15 mm 1 of 1…

A:

Q: Figure < 1 of 1 - 2 in. 0.5 in. - 2 in.-

A: For solution refer below images.

Q: In Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data: The diameter of part AB is dAB=100 mm The diameter of part BC is dBC=80 mm The length of…

Q: I need to find the forces in each tube but I keep getting stuck. I have been getting really long…

A: Given:To find:Force in each tube.

Q: A steel rod 8 mm in diameter is under the action of a tensile force (P) of 600 Newton. Calculate the…

A: Tensile stress is given by the following formula, Sigma=P/A Where P is the tension force and A is…

Q: TEST I: 1 Find Mhe allowable safe load P if the stresses in the bar are the folbuwing. AB= 56 cgi…

A: Given data:-Stress in bar AB, σAB=50ksi=344.738N/mm2Stress in bar BC, σBC=60ksi=413.685N/mm2Stress…

Q: 8- Following are the reading recorded at a point of structure tested by a 60° rosette: Ea =…

A:

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: The connection shown consist of five steel plates joined by a steel bolt with a diameter of 6 mm.…

A: The given information in the problem is shown in the following attached image:

Q: Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw…

A:

Q: Onv Problems 9-29 to 9-32 F 9-29 to 9-32 A steel bar of thickness h is welded to a vertical support…

A:

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that  A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data  Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: Segment AB of the bar is a tube with an outer diameter of 1.5 in. and a wall thickness of 0.125 in.…

A: Given:doAB=1.5 int=0.125 indBC=0.75 in

Q: O Torsion Аxial O Bending Transverse Shea O O

A: At point B the most impact on design will be of torsional shear stress, caused by the torsion.

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R₁ and R₂ The…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B…

A:

Q: Which of the following won't have the same unit as the others? Select the correct response: Stress…

A: Stress:  It is the ratio of internal resistive force per unit area of any object is known as stress…

Q: Question 1. P T The figure (not drawn to scale) shows a cylindrical column submitted to a combined…

A: Consider σx be the normal stress in x-direction and τxy be the torsional shear stress in xy-plane.…

Q: A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions…

A:

Q: 2-1. A standard steel specimen of Į in. dia- meter elongated 0.0087 in. in an 8 in. gage length when…

A: Given dataDiameter of the steel specimen d=0.5inElongation of the steel specimen e = 0.0087inGauge…

Q: A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod…

A:

Q: 1-Two rivets holds three sheets of steel together, and is loaded as shown below. If the maximum…

A:

Q: Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are…

A:

Q: Given a 2m-length rod with 23.0 mm diameter what is the actual stress (in MPa) if axial load is…

A: Given data :- The length of the rod (L) = 2 m                         The diameter of the rod (D) =…

Q: S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B…

A: given data; ⇒carry load(P)=100KN                       =100*103N⇒torque(T)=250 N-mm2⇒stress(σ)=350…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.