in your plant. The only place where this venturi can be attached to that system is by putting the venturi meter at 30-degree angles, as shown-an inverted U-tube manometer than been linked to that venturi meter because of space constraints at the lower part of the system. You need to make a complete report on the calculation and analysis of the water flow rate. You decided to start your study by creating a flow rate equation for this system, starting from the Bernoulli equation to make your statement clear. After deriving the flow rate equation, you determine the exact water flow rate for the system. Show what your report looks will be. Oil (SG = 0.85) 30 Diameter = 0.1 m Diameter = 0.3 m

in your plant. The only place where this venturi can be attached to that system is by putting the venturi meter at 30-degree angles, as shown-an inverted U-tube manometer than been linked to that venturi meter because of space constraints at the lower part of the system. You need to make a complete report on the calculation and analysis of the water flow rate. You decided to start your study by creating a flow rate equation for this system, starting from the Bernoulli equation to make your statement clear. After deriving the flow rate equation, you determine the exact water flow rate for the system. Show what your report looks will be. Oil (SG = 0.85) 30 Diameter = 0.1 m Diameter = 0.3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 150 mm diameter horizontal Venturi meter is installed in a 450-mm diameter water main. The deflection of mercury in the differential manometer connected from the inlet to the throat is 375 mm. (a) Determine the discharge neglecting head lost. (b) Compute the discharge if the head lost from the inlet to the throat is 300 mm of water, and (c) what is the meter coefficient?
In testing a fire pump, it is desired to flow 500 gpm (1890 liters per minute) from a 1 3/4-inch (45 mm) nozzle with a Cd of 0.97. What pitot pressure would indicate a flow of 500 gpm (1890 liters/minute)? QUESTION 9 A venturi meter with a 5-inch (125 mm) diameter restriction is located in a 6-inch (150 mm) pipe and gives a reading of 3.4 inches (8.6 cm) of mercury. How many gpm (liters per minute) are flowing? QUESTION 10 Solve for the coefficient of discharge of a device that delivers 45.5 gpm (172 liters/minute) from a 0.75-inch (20 mm) orifice when a pitot tube gives a reading of 15 psi (1.0 bar)?
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
A venturi meter is to be installed in a 4-in schedule 40 line to measure the flow of water at 60 F. The maximum flow rate is expected to be 300gal/min with w 50-in reading using mercury with specific gravity 13.6. What is the throat diameter specified for the venturi meter? If the venturi meter is replaced with an orifice, what throat diameter should be specified
How to measure coefficient of Discharge with the help of venturimeter? Explain in Detail.
A Venturi meter having a diameter of 6 in at the throat is installed in a horizontal 12-in water main. In a differential gage partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and the throat, what would be the difference in level of the mercury columns in inches if the discharge is 5.0 cfs? Neglect head loss.
Minor Losses A pipe system is comprised of a flush entrance, one gate valve, one 90° elbow, one 45° bend, and a globe valve. If the fluid flows at 11 ft/s, what is the head loss due to minor losses? O 12.4 ft O 14.3 ft O 22.5 ft 13.2 ft O 8.55 ft O 6.60 ft
Calculate the coefficient of discharge.
calculate the discharge through the venturimeter
Answer within 3-5 sentences only. 1. What is the purpose of a Venturi meter? 2. What is a hydraulics bench? 3. Write down the steps in calculating for the flow rate using the hydraulics bench. 4. When the flow rate is maximum, what happens to the difference in piezometric head between pipe 1 and throat pipe in the Venturi meter? 5. When the flow rate is minimum, what happens to the difference in piezometric head between pipe 1 and throat pipe in the Venturi meter?
Research atleast 4 venturi meter write the problem and solution legibly draw also the diagram if there is.
The throat area of a c-d nozzle is 10 cm^2 and its exit is 20 cm^2. If the stagnation pressure is 1 bar, what is the exit pressure (Pe) range needed to ?chock the throat greater or equal 0.935 bar O less or equal 0.937 bar O greater or equal 0.0935 bar and less or equal 0.937 bar greater or equal 0.937 bar and less or equal 1 bar O