In this pair number of binary joint is available. O A. four O B. one O C three O D. two

Q: A fillet weld can be used to join which of the following joint types: *

A:

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: esign of the Screw Jack. Lifting load – W, kN is 70.  Hight of lifting– H, mm is 500 Types of…

A: a screw jack is used to transfer the rotational movement into linear movement. It Uses a power screw…

Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned

A: Fillet welding is the process of welding to weld the 2 metals at an angle or perpendicularly.

Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned O Tee…

A: Correct answer: All of the mentioned

Q: swer the following: 1) Define the degree of freedom of a joint? 2) How many degrees of freedom does…

A: To define: 1) Define the degree of freedom of a joint?2) How many degrees of freedom does a c-joint…

Q: In which of the following joints, the connecting surfaces are inclined and not straight? O A Tlap…

A: For corner lap joint surface is inclined...

Q: Which one of them is permanently joint type  a) keyed joint  b) pinned joint  c) nut and bolt  d…

A: Keyed Joint: The Keyed joint is a detachable joint that is made up of key and keyways. These keys…

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: Output Input Figure.6: Universal joint or Hook’s joint.

A: As per our Q&A guidelines we are supposed to solve only first 3 subparts for a given question…

Q: of screw thread from ihe foll reasons for it. (2) (31

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Design the above joint using welded connection. The w=15mm. The required length of weld is:

A:

Q: 1.1 Brief description of work performed when welding a butt joint in a flat position 1.2The…

A: 1.1 Following steps and works are to be performed for welding a butt joint in a flat position:   1.…

Q: What type of support is at joint A?

A: The joint at point A is roller.

Q: Design a bolted joint to join the two members shown in the appropriate figure. Specify the number of…

A: See for similicity of design and calculation we take '4' bolt and class 9.8 bolt .Because 9.8 has…

Q: Find the eccentricity of the welded connection by using 5 mm fillet weld. -120 mm - 200 mm 400 mm X-…

A:

Q: Hard drawn copper rivets are u

A: Answer: d= 0.36in

Q: , the minimum metric specification required for the bolt is

A: Given, From the given shows,  Three bolt system having, Shear yield strength,σyt=200 MPaFOS=…

Q: the minimum metric specification required for the bolt is

A: Given, Determine the minimum metric specification required for the bolt ? where, Figure shown three…

Q: separately

A:

Q: Which of the following joints is a permanent joint? O A. Bolted joint O B. Riveted joint O C. Welded…

A: Permanent joint: The joint ensures a rigid mechanical attachment to parts over the entire process of…

Q: Two cables BG and BH are attached to frame ACD as shown.

A: The displacement vector from B to G is The unit vector along BG is

Q: Section A (An Q1(a) Explain types of pin jointed frames with examples.

A: given; explain type of pine joined frames with examples.

Q: Which among these joint consist of 3 degrees of freedom? a. Links and joints b. gripper c. wrist d.…

A: Degrees of freedom(DOF) can be expressed as the different ways in which a component can move. If a…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: In which of the following welded joints do both the work pieces are in the same plane? O A. Lap…

A:

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: The type of joint used in wooden photo frarnes is O A. Mitre joint

A: Ans-A. Miter joint.

Q: 1- Name the different forms of journal bearings. 2- Sketch with freehand and name the different…

A:

Q: Using the method of joints, de

A: first of all find out all required angle from geometry, then find reaction forces at B and C then…

Q: the bolt is

A:

Q: SoNe for a minímum bolt diameter minimum thickness of plate the rivets are atfached to Given: wad =…

A:

Q: Temporary joint is obtained by one of the following. (A) Interference fit (B) welding (C) Riveting…

A: Given data Temporary joint is obtained by one of the following

Q: 1- Name the different forms of journal bearings. 2- Sketch with freehand and name the different…

A: Journal Bearings

Q: -.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer…

A: Given data: The diameter of the bolt is D = 24 mm. The length of the bolt is L = 100 mm. Here, the…

Q: bolts required for an

A:

Q: ricated from a steel alloy g service use, the plate is

A: given:surface roughness kt=55MPamtensile stress σ=200MPaY=1

Q: True or False? The double-offset plunging-style CV joint uses a cylindrical outer housing with…

A: Double-offset plunging style CV joint :

Q: Large cars with long drive shafts often use a double-U-joint arrangement called a __ .a. Spicer…

A: A universal joint is a mechanical connecting device that is used between the rotating shafts and the…

Q: A constant velocity joint that is capable of in-and-out movement is a:   Select one: a. both…

A: Constant velocity (CV) joints are those joints that can facilitate the transmission of power from…

Q: A M16 x 2 hex-head bolt with to clamp together two 25-mm thick steel plates. a nut is used

A: GivenM16×2 hex-head boltt=25 mm

Q: Draw the FAD @ rod AB FBD

A: FBD is given below:

Q: Determine the number of pin joints 4. Which of the following has multiple degrees of freedom? OOO

A:

Q: (a) the minimum diameter required for shaft BC. (b) the minimum diameter required for bolt A.

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.