in this binary display, what is the denary value? LEDS LED4 LED3 LED2 =?

Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is…

A:

Q: What is program block and module .What is difference between "==" and "==="

A: Program block is new construct in System Verilog. The blocking and non blocking statement should not…

Q: Analog signals are in different from but a digital signal means only '0' or '1'. Only voltage among…

A: A continuous signal that represents physical measurements is known as an analog signal. Digital…

Q: Write a Boolean expression for the 4 to 1 digital multiplexer with data input ABCD and address…

A: to write a Boolean expression for the 4 to 1 digital multiplexer with data input ABCD and address…

Q: If a MOSFET is to be used in the making of logic gates application then it must work in O a.…

A: MOSFET should operate in cut-off and linear regions when used in logic gate applications. Because…

Q: clock cycles form one bus cycle. ROM can be classified into Dynamic ROM and Static ROM. Select one:…

A: 4 clock cycles are needed to form 1 bus cycle       RAM is classified into dynamic RAM and static…

Q: 2. Convert from Binary to Gray code: 11010100102 = _______________________ Gray code 3. BCD…

A:

Q: b) The diode is to be used in the AND logic circuit shown in figure Q1b : V DD R VA Vn Vo 0 0 Case 3…

A: Ans (1)  According to case 1 -: Logic across VA & VB = 1 (High) means voltage across the…

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A:

Q: without using the multiply the result that Serve to te devise Your MUL Instruction, write content of…

A:

Q: Q2/ a- Draw completely the BCD Decoder Driver (7442) IC with 7- segment display b- What is the type…

A: According to the question,

Q: Total Number of active low pins in IC74LS138? Options A-7 B-8 C-9 D-10

A: The answer is D-10 because For an active high pin, you connect it to HIGH voltage . the Pin having a…

Q: Q0 Q1 Q2 Q3 clock - Given: • Counter starts at decimal 9 when Q viewed as a 4-bit unsigned number…

A: Number   Unsigned        Signed (+ve)             Signed (-ve)              0…

Q: Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of…

A: Given data: $37 data at memory location $C100ACCA=$B8ACCB=$FE

Q: Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to…

A: Given data: 8 LEDs 74HC595 shift register Value of current LED=5 We have to find the value of the…

Q: Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and…

A: Assembly language is nothing but a code for computer's understanding. To assign a particular task to…

Q: What is the device address used by the instruction OUT A4, AL

A: OUT is a mnemonic that stands for OUTput Accumulator contents to an output port whose 8-bit address…

Q: In the following instruction sequence, show the resulting value of AL after highlighted comment, in…

A: The given instruction sequence is shown below: mov al, 01101111b and al, 00101101b,        ; mov…

Q: Draw the output waveform for the OR gate.

A: Need to draw the output waveform of the three input OR gate for the given input waveform…

Q: Find the unknown value for each of the following physical address. Assume all numbers are…

A: (a): The hexadecimal physical address can be found as: B2C0 : ???? = C2612 H So, B2C0 × 10 + FA12 H…

Q: How to store (1050000)10 in register $s0? Write down the instructions that stores the data in $s0…

A:

Q: Q6) Assume that we want to add the following instruction to the given MIPS single cycle data-path:…

A: According to the question, for the given MIPS operation, we need to find the condition of the…

Q: 6-bit parallel out shift register cik reset serial in 03

A: Given :    In the question they have mentioned diagram diagram ,it is very clear that they have…

Q: Convert the following Hex numbers to binary numbers: (a) : 2CE.6E8H

A: Convert  Hex numbers to binary numbers:  2CE.6E8H  To binary?

Q: Q1. Determine the contents of the register after execution of each instruction R16, $3F R18, $01…

A: Since you have posted multiple questions, we will solve the first question for you. If you require…

Q: To select the ROM the address lines A10-A9 should be:

A: The address line A10 in the given ROM connected to enable pin. By default it will select  1. The…

Q: Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature…

A: Range of temperature is from 27 to 100 oF Actual temperature is 40 oF now, Resolution using 7 bit…

Q: A certain gate has a Speed Power Product of 35 pico Joules and IcH= 0.5mA and =2mA with a dc supply…

A:

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A: From the given options                                                       IO¯/M   =1  : operation…

Q: Q2: Consider a line of code- LDD $C100. Before execution of this line of code, the memory locations…

A: We need to select correct option for given statement

Q: 1. Write the data (10010000)Gray in BCD code.

A:

Q: Consider a 12-bit ADC with a voltage reference (Vret) from -1V to 5V. If the input voltage (Vin) is…

A: We are authorized to answer the first question since the exact one wasn’t specified. Please submit a…