Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is the content of SI after executing the MOV SI, [DI+BX+7H] instructions? * Memory Memory address content 11 AA 12300 12301 12302 EF 80 | 47 12303 12304 12305 8D 12306 5A 12307 92 12308 C5 SI = EF80H SI = 80EFH

Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is the content of SI after executing the MOV SI, [DI+BX+7H] instructions? * Memory Memory address content 11 AA 12300 12301 12302 EF 80 | 47 12303 12304 12305 8D 12306 5A 12307 92 12308 C5 SI = EF80H SI = 80EFH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

20. Suppose we have just found yet another representation for floating point numbers. Using this representation, a li2-bit floating point number has 1 bit for the sign of the number, 4 bits for the exponent and 7 bits for the mantissa, which is normalized as in the Simple Model so that the first digit to the right of the radix points must be a 1. Numbers in the exponent are in signed 2's complement representation. No bias is used and there are no implied bits. Show the representation for the smallest positive number this machine can represent using the following format (simply fill in the squares provided). What decimal number does this equate to? : SIGN EXPONENT MANTISSA
Assume that the content of A is $A7 and that the content of B is $20. Find the contents of A and B after the MUL instruction is executed. [Hint: The MUL instruction assumes that the contents of A and B are unsigned integer values.]
Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit. The tpcg = 0.5 ns, tccq = 0.25 ns, tpd = 4 ns, tcd = 2.5 ns, tsetup = 0.5 ns and thold = 0.2 ns. What is the maximum value of fc? Select one: a. 0.2 ps O b. 200 MHz O c. 2 GHz O d. 200 KHz
Question 1: Consider the following assembly language program. Determine the internal memory location after every MOV instruction in the program. RETMON EQU OF000H ORG 100H START MOV R5,#25H SETB PSW.4 MOV R6,#67H SETB PSW.3 MOV R4,#36H CLR PSW.4 MOV R7, #89H LCALL RETMON END
This question is from the subject Digital Logic Design. Assume your register number FA19BSExxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary. b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SP20-BCS-156.
Which system has a base 16? A. Octal B. Decimal C. Hexadecimal D. Binary
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.
assembly 8086
a) An 8-bit shift register holds the data word 00111100. What will the register contents be after three right shifts? (Assume that serial input=D0) b) Draw the above shift register circuit using negative edge triggered D FFs
i need the answer quickly
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.