"In the steady conduction process, the heat transfer process occurs due to a temperature difference. If we analyze a conductive heat transfer in a gas pipe that is used to convey hot gas, the heat transfer occurs from the hot gas out of the pipe radially. To reduce the rate of heat transfer, what can we do?"

"In the steady conduction process, the heat transfer process occurs due to a temperature difference. If we analyze a conductive heat transfer in a gas pipe that is used to convey hot gas, the heat transfer occurs from the hot gas out of the pipe radially. To reduce the rate of heat transfer, what can we do?"

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.77P: 1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel...

See similar textbooks

Similar questions

V:01 Expert Q&A Done Question 1: In your own words, write down the differences between thermodynamic and heat transfer. (3 Marks) Question 2: Estimate the heat loss per square metre of surface through a brick wall 0.5 m thick when the inner surface is at 400 K and the outside surface is at 300 K. The thermal conductivity of the brick may be taken as 0.7 W/mK. (2 Marks) Question 3: A furnace is constructed with 0.20 m of firebrick, 0.10 m of insulating brick, and 0.20 m of building brick. The inside temperature is 1200 K and the outside temperature is 330 K. If the thermal conductivities are as shown in the figure below, estimate the heat loss per unit area. (5 Marks) 1200 K 330 K Insulating brick X-0.10m k= 0.21 Ordinary brick X=0.20 m Fire brick X= 0.20 m k= 1.4 k= 0.7 (W/mK)
Question six(Heat Transfer) In a heat transfer equipment in a laboratory you used a pipe of outside diameter 9cm to convey steam to reduce the heat outward flow from it to the surroundings. You decided to pad the pipe with two layers of insulating materials each 3cm thick. One from the inside, and the other from the outside. the conductivity of one material being 4times that of the other. I. Show quantitavely that the combined conductivity of the two layers is 28% more when the better thermal insulating material is put on the inside. II. What percentage would the combined conductivity of the two layers be if the better insulating material is now placed on the inside.
In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conduction
Hello. Can you please help answer the question shown in the photo? It is a 3-part question which I have attempted many times. I was able to calculate the correct answer for part 2, but part 1 and part 3 still says I am incorrect. Please show how to properly solve the problem. The topic is heat transfer. Thank you.
Determine the heat conduction of a boiler if you are given the following data: The thickness of the boiler is 15 cm, the T1 is the temperature of the water is 25°C and the T2 of the steam is 110°C, the thermal conductivity The boiler material is iron (use presentation table), the boiler area is 4.5 m^2
Heat Transfer question In order to cool down a hot steel sphere (its diameter is 5 cm), CO2 gas is blown over it through a pipe with a diameter of 10 cm. The CO2 gas is kept at atmospheric pressure while moving through a smooth pipe at a speed of 6 m/sec. The gas temperature entering the pipe is 300K and exiting the pipe is 340 K. The pipe temperature at the entrance is 350K and at the exit is 550K. The sphere is located just about the pipe exit. Find the convective heat transfer coefficient of the gas moving in the pipe, the heat transfer rate at the pipe and the pipe length. What is the surface temperature of the sphere if the heat transfer rate between the sphere and the gas is 7W and its surface temperature is higher than the gas?
My buddy is starting to get hypothermic (body temperature 306 K) during an epic backcountry ski adventure. Since I'm quite warm (body temperature 310 K), I decide to get in a sleeping bag with him to try and warm him up. What heat transfer mechanism will be most responsible for heating him up? For simplicity, ignore any internal temperature differences across my body (that is, assume my skin temperature is also 310 K). Use numbers to support your answer (for human skin, you can use the following values: surface area A = 1:50 m2, emissivity = 0:970, thickness d = 0:0250 m, thermal conductivty 0:200 JmsK)
What is the solution to the engineering subject in Thermodynamics 2 picture i uploaded. Thanks so much
Hello sir Can you solve this problem because i did'nt understand about subject (heat transfer)
se Finals prep & more: Get help from live tutorsTry bartleby tutorarrow_forward Question Asked Jun 17, 2020 1 views As a researcher in the field of heat transfer, how will you distinguish between radiation by black body and a real body? Explain briefly Point out and briefly explain the various factors affect the thermal conductivity of a material. What is the analogical reason between heat transfer by conduction and flow of electricity through ohmic resistance? Use a composite wall of a building to illustrate the concept.A composite slab with three layers of thermal conductivities k1, k2, k3 and thickness t1, t2, t3 respectively, are placed in a close contact. Derive an expression from the first principle for the heat flow through the composite slab per unit surface area in terms of the overall temperature difference across the slab. Based upon the reradiating properties of absorptivity, reflectivity and transmissivity, how would you distinguish between the…
What is the the answer to the picture of Thermodynamics subject in engineering I uploaded
Hello, I am a mechanical engineering student and want to upload this question as I have an exam in early June about thermodynamics. I have been given a question that will help me answer my exams in June. Please could you answer showing step by step guidance on how to answer this question with the formula clearly shown. Thank you very much