In the given figure below, the force F has a magnitude of 440 lb and direction as shown (D to A) 6 m D 7m 6 m 3 ml4im 2 n 3 mi 6 m Determine: A. The component of moment My parallel to line BC.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: _____ is an example for indirect stress Select one: a. Shear b. Bending c. Tensile d. Compression

A:

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: Please check for the question, verify it is correct or not?

A: There is a half cylinder with length L and radius r.Incoming air velocity is uCoefficient of the…

Q: Which of the following is least likely to be found on a basic parts list? A. Find Number B. Quantity…

A: Find number refers to the ordering number that gives an ID tag to one of the parts in a parts list…

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: Determine the magnitude of the resultant force FR = F₁+F₂ and its direction, measured clockwise from…

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: What do you mean by Redesign the structure so it is more tolerant of statements

A: Given  Redesign the structure so it is more tolerant of statements To find Meaning of the statement…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: This a sketch of what process. V, F Punch Flash Die Cutting edges Select one: a. Cutting O b.…

A: The given sketch represents Trimming process. Trimming process: The shearing of the excess material…

Q: Mold is manufactured in two parts top and bottom, size has to be smaller than the actual size of the…

A: As per given question  Mold is manufactured in two parts top and bottom, size has to be smaller than…

Q: Whats the formulae for temperature error %

A:

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: what is the bottom length?

A: To calculate the bottom length

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: Draw and state Vernier Calliper Parts?

A:

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: What is the sliding block?

A: To Define: Sliding block

Q: Hydraulic fracturing is a method of breaking open cracks and fissures in the se Correct Answe Pay…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: This was not correct may you please

A:

Q: 0le A. An outside caliper can be used to measure the diameter of a

A: Caliper is used to measure the linear dimension, diameter of a hole and outer diameter of a shaft.…

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.