The type maintenance requires periodical inspection and testing.

Q: _____ is an example for indirect stress Select one: a. Shear b. Bending c. Tensile d. Compression

A:

Q: 20-  Vickers Hardness Number (HV) value is directly proportional to  a. Shape of indenter b.…

A:

Q: Which data should be considered to evaluate the effectiveness of maintenance?

A: Mean Time Between Failures (MTBF): Definition: MTBF is the average time elapsed between the…

Q: For what purpose is a torsion test performed?

A: The torsion test is used to determine the shear properties of the material. In this testing, the…

Q: State one advantage and disadvantage of compression testing.

A: Compression testing: It is a strength test method of material under compression. For testing the…

Q: ow cost of investment for breakdown maintenance which after the occurrence of an advanced considered…

A: Yes, It is true.

Q: 27,000 26,500 25,000 1.50 (maximum load) 2.10 2.79 (fracture) Pull test result data in Table 1.…

A: Force (N) deflection ((∆l) stress ((σ) MPa strain 0 0 0 0 5000 0.0296…

Q: 1. List the seven types of failure 2.Define die penetrant test 3.Suggest N.D.T.test for an internal…

A: subject : Material Science

Q: Industrial pipes: Can we perform hydrostatic testing immediately after completion of…

A: The objective of the question is to understand if hydrostatic testing can be performed immediately…

Q: Describe the working and environmental conditions that lead to failure for a product made from…

A: The auxiliary judgment of conventional FRP components in destructive situations is as a rule…

Q: View Policies Current Attempt in Progress Calculate the moment Mg of the 945-N force about the bolt…

A:

Q: 1. Please select the effects of vibration * Human discomfort Increase strain rate Structure buckling…

A: Vibration: Any unwanted to-and-fro motion of  the body about its equilibrium position is known as…

Q: List the important information that should be considered in planning a reliability test programme.

A: Steps are given in next step.

Q: were analysed and were as presented in Figure 5.1 below. Based on this figure, answer the following…

A:

Q: In a good material handling system timely movement of materials is possible. Select one: True False

A: Given Data⇒ Material handling system Timely movement of materials

Q: Welds machining tool marks and stress reversal such as those in rotating parts can cause a…

A: Welds machining tool marks and stress reversal such as those in rotating parts can cause a…

Q: Endurance limit is the stress level at which the materials fails at (industrially defined) infinite…

A: According to the given dataWe need to findCorrect optionThat fits to the defination of the endurance…

Q: Penetrant testing Procedure below with Dwell time, and Minimum three defect that can be detected…

A:

Q: Choose only one of the maintenance tasks identified and describe what materials and tools will be…

A: To find:Choose a maintenance task, mention the tools required, safety measures to be taken and…

Q: How can the inspections and tests be made promptly andtimely by the Inspector?

A: The need to perform inspections as regular is to ensure the proper working of all the industry…

Q: A standard is intended to achieve which one of the following: a. Design b. Performance c.…

A: A standard is intended to achieve

Q: 6. Gas turbine engine parts can be successfully inspected only for surface defects by: O Visual…

A: To choose: The correct option: Given: The gas turbine engine parts is successfully inspected only…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Q: why do we physically mark gauge length on the samples before the test even though the machine is…

A: Solution: Given Data: Tensile Testing Machine   To Find: (a) Why do we physically mark gauge length…

Q: :In impact testin

A: Hi and thanks for the question. Since you have asked multiple questions, we will solve the first…

Q: is a measure of internal resistance caused by electrical environment of the particles. a. Effective…

A: Given :-  is a measure of internal resistance caused by electrical environment of the particles. a.…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: Answer the following question: 1. What are the the things that needs to be checked when performing…

A: Answer- 1-  The federal Aviation Regulations(FAR) requires the inspection of all civil aircraft at…

Q: An experimental device imparts a force of magnitude F-34 lb to the front edge of the rim at A to…

A:

Q: What are the significance of tolerance and allowance in production process? Diagram?

A: Tolerance and Allowance

Q: 1. If maximum stress is 200Mpa, stress amplitude is 50Mpa, minimum stress is 100Mра. ( ) 2. For the…

A:

Q: What are the different types of hardness test? Write a detailed note on each type.

A: Hardness is the ability of the material to resist scratch or indentation. Hardness is also defined…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: :Measurement of vibration is required to

A: GIVEN DATA A MCQ GIVEN ASKING VIBRATION MEASUREMENT REQUIRED TO WE HAVE TO CHOOSE CORRECT OPTION

Q: During Destructive test, the specimen is a. Not broken b. not affected c. Damaged d. Not damaged

A:

Q: Explain four safety features in doing Mechanical Integrity Tests?

A: Solution:

Q: Place a check on the space corresponding to the observed physical properties. Metal brittle…

A: Magnesium denoted as Mg, is a lustrous metal, it is a malleable, soft, and ductile metal. Since it…

Q: What type of indentor is used in a Brinell hardness test? Select one: O a. rhombus shaped O b. None…

A: Hardness test focuses on measuring the hardness of a specimen by subjecting it to indentations with…

Q: Pre-Condition Post-Condition Weakest Pre-Condition \sStrongest Pre-Condition

A:

Q: Which fixture would be the most suitable for welding up and drilling the holes for fixture for the…

A: Modular fixture is most suitable for welding up and drilling the holes for fixture for the complete…

Q: List the 2 aspects that need to be considered when temperature testing for reliability

A: Given Temperature measurement To find Reliable temperature measurement

Q: Briefly define the purpose, types and construction of the hardness measurement.

A: The principal purpose of the hardness measurement  is to determine the suitability of a material for…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.