In the following multiple-choice problems, circle the one answer which best completes theSentence(i)(iii)(iv)(v)The glass transition temperature of polystyrene is about 110 °C. Relative to a sampleat 120 °C, at room temperature polystyrene is:a. orders of magnitude more viscousb.slightly more viscousc. equally as viscousless viscousd.e. none of the above.The glass transition temperature of polystyrene is about 110 °C. Relative to a sampleat 120 °C, a sample of polystyrene at 130 °C is:a orders of magnitude more viscousb. slightly more viscousc. equally as viscousd. less viscouse.none of the above.Suppose a tensile test is performed on two identical materials except that one has adeep scratch on its surface whereas the other is perfectly smooth. Relative to thesmooth specimen, the test will find that the scratched specimen has a lower.a. elasticityb. yield stressc. tensile stressd.elongation to failuree. none of the above.Thermoplastic polymers such as polyethylene can be melted relatively easily, because:a. they are highly crosslinked by a curing agent,b. the bonds between molecules are primarily covalent,c. the monomer units are short,d. the intermolecular bonds are relatively weak secondary bonds,e. none of the above.The two sketches below represent the microstructure of two specimens with identicalaverage composition but subjected to different annealing treatments.a. A is stronger and more ductile than B,b. B is stronger and more ductile than A,c. A is stronger but more brittle than B,d. B is stronger but more brittle than A,e. none of the above.AB

The correct options. “Since you have posted multiple questions with multiple sub parts, we will…

In the following multiple-choice problems, circle the one answer which best completes the Sentence (i) (ii) The glass transition temperature of polystyrene is about 110 °C. Relative to a sample at 120 °C, at room temperature polystyrene is: a orders of magnitude more viscous b. slightly more viscous c. equally as viscous d. less viscous e. none of the above. The glass transition temperature of polystyrene is about 110 °C. Relative to a sample at 120 °C, a sample of polystyrene at 130 °C is: orders of magnitude more viscous

In the following multiple-choice problems, circle the one answer which best completes the Sentence (i) (ii) The glass transition temperature of polystyrene is about 110 °C. Relative to a sample at 120 °C, at room temperature polystyrene is: a orders of magnitude more viscous b. slightly more viscous c. equally as viscous d. less viscous e. none of the above. The glass transition temperature of polystyrene is about 110 °C. Relative to a sample at 120 °C, a sample of polystyrene at 130 °C is: orders of magnitude more viscous

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Summarize how at least two reference materials relate to the basic scientific principles of flying a paper plane. Each reference material must come from a different source. Be sure to describe how the references provide a foundational background for the experiment.
Surface tension is due to uneven molecular attraction between immiscible fluid media and solid surface. Its importance is governed by dimensionless parameter Which of the Inertia force called Weber number given by We = Surface tension force™ following statements are correct? (i) Surface tension becomes important when the length scale L is small such as in ink jet printing, coating of thin film, oxygenation of water by falling rain drops. (ii) 111 Super-hydrophobicity can be achieved by micro/nano texturing of surface such as in lotus leave, butterfly and dragonfly wing. During oil spill in ocean, oil floats and spreads out due to gravity. By conservation of mass, the oil film becomes thinner as it spreads. Finally, the surface tension force becomes important causing the formation of tiny oil droplets. (A) (B) (C) (D) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above
Please answer it correctly and read carefully. SHOW SOLUTION STEP BY STEP PLEASE
16000 1.440 14000 1.435 12000 1.430 10000 1.425 8000 1.420 6000 1.415 4000 1.410 2000 1.405 1.400 45 15 20 25 30 35 40 Temperature ["C] +dynamic viscosity (mPas] + density (gicm") Figure 1 (a) As shown in Figure 1, viscosity and density of honey was found to decrease with increase in temperature. Explain the reasons behind these phenomenon related to Fluid Mechanics in microscopic view. Dynamic viscolsty [mPa.s] Density [g/cm³]
Q1. Honey is a very widely used ingredient in cooking all around the world. Many commercial honey manufacturers heat treat honey to remove harmful bacteria that may be present. The density and viscosity of the honey varies with temperature, as shown in table 1. Temperature K 293 298 303 308 313 318 323 Density kg/m³ 1403 1398 1393 1388 1383 1378 1373 Viscosity Pas 55.66 46.45 37.99 30.28 23.32 17.11 11.65 Table 1: Fluid properties of honey. A particular processing facility heats and sterilises 500 kg of unprocessed honey every 30 minutes. The unpro- cessed honey is stored in large vats, then pumped though pipes into heating units before being pumped through another pipe to be bottled. The pipe carrying the honey from a storage container, which is 11 m tall, to a heating unit is 5 m long and has a diameter of 10 cm. Prior to being heated the honey is kept at 25°C. (a) What is the pressure difference between the top and bottom of a storage vat when it is full? (b) What is the volume flow…
Please answer within one hr i will give good rating.
Using the value of 0.55s ± 0.17s calculate the value for g and the value for uncertainty in g. Using the formula provided in image.
A light bulb manufacturer wants to maximize bulb lifetime. Four parameters are to be tested: Parameters a and b are the concentrations of a certain alloys in the filament. Parameters c and d are the temperature and speed, respectively, at which the filaments are extruded in the manufacturing process. A three-level experiment is be used. Levels 1, 2, and 3 correspond to low, medium, and high values of each respective parameter. Taguchi's 9-run design array (as in the learning module) is to be used. For each experimental run, thirty bulbs are tested, and the mean time to failure (MTTF) for each run is recorded as X₁, X₂, etc. These values, in order, are 1318, 1375, 1414, 1490, 1532, 1296, 1455, 1219, and 1266 hours, to four significant digits. (a) Generate a table with the above values configured as a Taguchi 9-run design array (Excel is recommended). Calculate all 12 level averages, i.e. Xal, Xa2, X3, Xb₁‚ Ãµ2, Xd3 (b) Generate four plots, showing the dependence of X on each parameter.…
Please show all possible workings, such as how the matrix was derived and how the answer was reached. Use finite element analysis.
What’s the correct answer please?
Can you help with both please.