In the following figure the long tube is filled with water at 20°C. When valve A is closed,P₁-P₂ = 75kPa. When valve A is open and water flows at 500 m³/h, P₁ – P₂ = 160kPaWhat is the loss in lift due to friction between 1 and 2, for the condition in which the waterflows? (p = 998 kg ,g = 9,812)m 731)BombaR.SA(2)

Givenwhen valve is closed P1-P2=75 kPawhen valve is openQ=500 m3/h=500 3600m3/s=0.1388…

In the following figure the long tube is filled with water at 20°C. When valve A is closed, P₁ – P₂ = 75kPa. When valve A is open and water flows at 500 m³/h, P₁ P₂ = 160kP What is the loss in lift due to friction between 1 and 2, for the condition in which the wat flows? (p = 998 kg , g = 9,811)

In the following figure the long tube is filled with water at 20°C. When valve A is closed, P₁ – P₂ = 75kPa. When valve A is open and water flows at 500 m³/h, P₁ P₂ = 160kP What is the loss in lift due to friction between 1 and 2, for the condition in which the wat flows? (p = 998 kg , g = 9,811)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the following figure showing a jet of water supporting a weight of 100 N at aheight of 5 m . Water leaves the nozzle with a velocity of 20 m/s. The diameter d ofthe nozzle will be
A room has a volume of 349 m3. An air-conditioning system is to replace the air in this room every 81.5 minutes, using ducts that have a square cross section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is (a) 2.00 m/s and (b) 7.00 m/s. a: b:
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50g and is charged with 100g of water. The pressure inside the rocket is 100kPa gage. The exit area is one-tenth of the chamber cross-sectional area. The inside diameter of the rocket is 5cm. Assume that Bernoulli’s equation is valid for the water flow inside the rocket. Neglecting air friction calculate the maximum velocity it will attain.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
The horizontal nozzle in Figure has D; - 12 cm and D2 - 4 cm, with inlet pressure p1 200 KPa absolute and V2 - 10 m/s. For water at 20°C and density of 1000 kg/m3, compute the horizontal force provided by the flange bolts to hold the nozzle fixed. The atmospheric pressure is 100 KPa. Open jet Water
Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The fluid flowing through it is 10 °C liquid water; A₁ = 1.2 m², A₂ = 0.300 m², V₁ = 15 m/s, p2 = Patm and p₁ = Patm + 75 kPa. Neglect effects of gravity. Fx= i Fy= i A1 P1 KN kN Fy ZA A2, P2 = Patm Fx 45° Patm
Consider the following compressor that receives air at a constant rate of three cubic feet per second. Air exits the compressor at a pressure of 95 pounds per square inch and 425 °F. Assume that there are no changes in potential or kinetic energy. With the assumption that there are constant specific heats, what is the power, in hp, consumed by the compressor? Surrounding P1=14.5 psi and T1= 68 °F
The jet engine on a test stand, shown in the figure, admitsair at 20oC and 1 atm at section 1, where the area is 0.5 m2and the velocity is 250 m/s. The fuel-to-air ratio is 1:30.The air leaves at section 2 at atmospheric pressure and ahigher temperature. The exit velocity is 900 m/s and thearea is 0.4 m2. Compute the horizontal test stand reactionRx needed to hold the engine fixed.
Air flows at the rate of 1.5m/s through a horizontal pipe with a gradually reducing cross-section as shown in the figure. The two cross-sections of the pipe have diameters of 400mm and 200 mm. Take the air density as 1.2 kg/m³ and assume inviscid incompressible flow. The change in pressure (P2-Pj) (in kPa) between sections 1 and 2 is 200mm ! (1) ↑ Air Flow 400mm (2) 1.5 m³ /s (A) –1.28 (B) 2.56 (C) -2.13 (D) 1.28
338 B/s O 1: 56% E 3:01 Question: Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-1 6 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. (2 1
Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
An airplane is flying at a velocity of 150 m/s at standard sea-level conditions. The temperature at a point on the wing is 270K. What is the pressure and velocity at that point? For air, C, = 1008- %3D kg K