In the figure shown, the inside diameters of the pipe at sections 1 and 2 are 250mm and 500mm, respectively. Water with a unit weight of 9.59 kN/m3 is flowing with an average velocity of 8 m/s at section 1. Find the Velocity of flow at Section 2. Control Volume a, az 2 V2 Unit of the Correct Answer: m/s O 2.00 0.50 4.00 O 1.50

In the figure shown, the inside diameters of the pipe at sections 1 and 2 are 250mm and 500mm, respectively. Water with a unit weight of 9.59 kN/m3 is flowing with an average velocity of 8 m/s at section 1. Find the Velocity of flow at Section 2. Control Volume a, az 2 V2 Unit of the Correct Answer: m/s O 2.00 0.50 4.00 O 1.50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hydraulic Toolbox 3
A parallel pipe system is shown in the figure. The total flow on the system is 0.86 m³/s. Determine (a) the flow in pipe 1 in m³/s, (b) the flow in pipe 2 in m³/s, and (c) the flow in pipe 3 in m3/s.
3
8.14 A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity.
Pb-8a.
Determine the diameter of the pipe if the fluid flows @ 20 L/s and the velocity head is 5m in mm *
In the pipe systems (a), (b), and (c) in the Figure, find the flow and velocity in each pipe and the pressure at points A. Assume all nodes are at identical elevations. m/min 20 m/min 20 m /min P- 1000 kP Sm/min 1500 m 1000 m 455 mm 405 mm 1000 m 405 mm 800 m 255 mm 300 m305 mm 300 m 205 men 1100 m 305 mm 1000 m 305 mm A500 m 205 mm 10 m/min 5m/min 10m3/min 5 m/min 15 m /min 5m/min Elev 300 m 405 mm 2000 m 150 2000 m Elev 250 m 5m/min 10 im/min 6 m/min 205 mm 205 mm 2000 m A 2000 m le) 000
The circular water pipes shown in the sketch are following full. The velocity of flow (in m/s) in the branch pipe "R" is V = 6 m/s dia = 4 m – મ N=? R V = 5 m/s dia= 2 m
The total discharge (flowrate) from A to B in the figure below is 300 liters/s. Pipe lennthe are: L1= 150 m, and L2 = 450 m. Diameters, are: D1 = 500 mm, and D2 = 250 mm. L1:D1 Q1 Q Q2 L2; D2 Determine [Using Darcy's equation] the headloss [m] and the flowrates (/s] across A-B in pipes 1 and 2 if riyated steel iron pipes are used in the system and flow is FULLY TURBULENT. Flowrate pipe #1 [I/s] =- Flowrate pipe #2 [l/s] =- Headloss pipe #1 [m] =. %3D Headloss pipe #2 [m]
The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the branch pipe "R" is PI V = 6m/s, dia = 4m - = V = ? R Q V = 5m/s dia = 2m
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
Determine the flow rate that circulates through each of the pipes in the system shown.