In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and theloss at nozzle of 0.05 times the V2²/2g, determine the discharge and head H.Ans: 0.0136m³/s & 2.731mA150mm diaWit50mm dia

Answered: Image /qna-images/answer/1015670c-d6df-45ad-987e-a6eb57050078.jpg

In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the loss at nozzle of 0.05 times the V22/2g, determine the discharge and head H. Ans: 0.0136m³/s & 2.731m

In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the loss at nozzle of 0.05 times the V22/2g, determine the discharge and head H. Ans: 0.0136m³/s & 2.731m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The siphon in the figure has a nozzle 150mm long attached at section 3 reducing the diameter to…

A: A siphon is attached to tank as shown in the figure has, length of nozzle = 150mm diameter of nozzle…

Q: A booster pump is installed in the pipeline between the two reservoirs. If the energy head increased…

A: Booster pump is installed in the pipeline between the two reservoirs A and Bthe energy head…

Q: Calculate the surface tension of the fluid (SG = 8.6) in the capillary tube below: Зтт h = 2mm e =…

Q: A capillary tube of 1.3 mm diemeter is immersed vertically in water exposed to the atmosphere.…

Q: The liquid in the figure has a specific gravity of 3.00. The gage pressure P₁ =700 KPA and PB is…

Q: This is an open-top cylindrical tank* height of tank = 4 meters diameter of tank = 2 meters The…

Q: 7. A heavy Oil (y = 9000 N/m³) is flowing at a rate of 0.65 m³/s in the system shown. If the total…

A: Q = 0.65 m3/s HL = 2.5 m PB = 70 kPa

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

Q: Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage.…

A: The given data is shown below: Specific gravity=0.75Pressure at A=142 kPa

Q: A liquid of specific gravity SG = 1.62 flows in a 75 mm diameter horizontal pipe. The total energy…

A: Specific gravity of liquid, SG =1.62Diamteter of pipe, D=75mm =0.075mThe total energy at a point, E…

Q: AcylinuTIcal laiiK Tlavilng a uldilitit UI ZII and height of 4m is open at one end and closed at the…

A: γw=9.81 KN/m3

Q: - In a mano meter shown, the fluid from A to B is mercury (s-g. 13.0) and from e to C, the flud is…

A: Given data in question Specific gravity of mercury Spacific gravity of oil Pressure at point C…

Q: The diameter of an open topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m…

Q: Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 h.l. 2.3m do:…

A: Given data: diameter of tank 1 D1=6m Dimensions of tank 2 are 3m x 2m Difference in water level h=…

Q: In the supply system (Q=0.89cfs) shown in the figure, the pressure required at the delivery end is…

A: Q = 0.89 cfs Diameter = 4 in = 0.333 ft Length = 1000 ft Pressure at delivery end = 65 psi Water…

Q: The centrifugal pump blades are 20 mm in depth at the outlet. The impeller is 250 mm in diameter and…

A: A centrifugal pump's impeller features backward-facing blades that are angled at 30 degrees to the…

Q: Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What…

A: The values and diagram given in the question are as follows The specific gravity of glycerine=1.26…

Q: Find the Pressure and the total energy at the points A, .. , E 10m+ SFD Bx 100m 10m+SFD E 100m 60m…

Q: Problem 4 In the figure shown, suppose that the reservoir is open to the atmosphere at the top. The…

A: Detailed solution is given below, still if you have any query please feel free to contact me.Thanks…

Q: For constant density flow through this round nozzle, V₁ = 1.7 m/s and V₂ = 20 m/s. The ratio of…

Q: A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at point %3D 1 and 2…

Q: Statement I given specific energy the discharge 1 maximum when the flow is critical For d is (Fr…

A: given- critical flowFroude's number Fr=1 It is required to prove that, for a given specific energy…

Q: Calculate the force required to hold a flat plate in equilibrium perpendicular to the flow of water…

A: Calculate the force required to hold a flat plate in equilibrium?

Q: The centerline of the standard orifice is 3.2 meters above the ground and 3.5 meters below the…

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

Q: The triangular valve (AB) which weighs 1500 Newtons closed at point A and is free at point B. What…

A: Length of the gate t=2sin50o=2.6108 m Depth of center of gravity from surface of water…

Q: The ratio of the momentum correction factor to the energy correction factor for a laminar flow in a…

Q: A pressurized tank discharges its alcohol through a square orifice (c = 0.64, cy = 0.97). If minor…

A: step 1-

Q: 1. For the frictionless syphon shown, determine the discharge and the pressure heads at A and B.…

Q: The ligure shoWs a tank discharging through a pipe with a nozzle at Its end. Find the discharge and…

Q: The open tank with piezometers attached on the side, contains two different liquids. Find the…

A: As the liquid in piezometer A and liquid in tank above the installation point of piezometer A is…

Q: A solvent used for plastic manufacturing consists of cyclohexanol in tank A and ethyl lactate in…

A: Specicific gravity of cyclohexanol, Sc=0.953Specific gravity of mercury, SHg=13.55Specific gravity…

Q: In the following system, the flow rate of Q = 400 It / s is transmitted from the A chamber to the B…

A: The liquid from one chamber to another chamber due to variation in height and pressure…

Q: Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in…

Q: Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is…

A: NPSH is the net positive suction head, which is measured in the centrifugal pump.If the local…

Q: A liquid of specific gravity SG = 1.76 flows in a 77 mm diameter horizontal pipe. The total energy…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the
loss at nozzle of 0.05 times the V2²/2g, determine the discharge and head H.
Ans: 0.0136m³/s & 2.731m
A
150mm dia
Wit
50mm dia

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

M3
Please explain so I can understand
Argon gas flows through a well-insulated nozzle at steady state. The temperature and velocity at the inlet are 570°R and 150 ft/s, respectively. At the exit, the temperature is 460°R and the pressure is 40 lb/in². The area of the exit is 0.0085 ft². Use the ideal gas model with k = 1.67, and neglect potential energy effects. Determine the velocity at the exit, in ft/s, and the mass flow rate, in lb/s.
A cylindrical tank with its axis horizontal has a length of 6 m and the ends of the tank are vertical planes, as shown in Figure Q2 (a). The vertical pipe of 0.2 m in diameter is connected to the top of the tank. The tank and the pipe are filled with ethyl alcohol to a level of 1.5 m above the top of the tank. The diamter is 2.07m.
A 12.5mm diameter orifice at the vertical side of the tank showed a discharge of 60 liters for every 85 seconds at a constant total producing head of 4.5m. Measurement of the jet showed that it travelled 2.4m horizontally while dropping 400mm. Determine the coefficient of discharge. A) No Answer among the choices В 0.612 C) 0.637 D 0.584 E 0.668
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
Q1: Derie an epressin for the shear stress at the pipe wall when an incompressible faid flows draugh a pipe wnder pressure. Use dinmsional ana)sis witk the following siguißcant parameters: pipe diameter D, flow velociy V, and vicenity and density p of the fuid. Q2: : Use dinensional analysis to derive as epression for the power develaped by an engine in terms of the torque T and rotartive speed u.
A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?
Q3) In impact of jet experiment if the supplied discharge Q through a 5 mm diameter nozzle is (0.25 L/s), find the required weight W that is needed to support the plate in its initial position as shown in figure. 50 mm W Nozzle