Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in the figure below. f = 0.0161 h1 = 5.95 m h2 = 12.10 m L1 = 69 m Required Compute the pressure at point B in kPa to the nearest 10th, considering the energy loss due to friction, but neglecting other losses. 1.5 m h1 100-mm OD x 3.5-mm wall h2 copper tube Flow B L1

Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in the figure below. f = 0.0161 h1 = 5.95 m h2 = 12.10 m L1 = 69 m Required Compute the pressure at point B in kPa to the nearest 10th, considering the energy loss due to friction, but neglecting other losses. 1.5 m h1 100-mm OD x 3.5-mm wall h2 copper tube Flow B L1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.12 O -0.12 8.33 (1) Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. O-8.33 -L h e - - - -
A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another gage at elevation 7 m reads 140 kPa. Compute the density of the liquid. L00 kPa - El. 12 Sm 140 kPa - El. 7
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the flow rate of the oil in the pipe if the total head loss from point 1 to point 2 is 12 m of oil. 160mm 200mm s EL 200m El.150m Oil. Sp.gr.=0.82
Shown in figure, A pump discharged 0.05 cu. m/sec. water from a 220 mm suction pipe and delivers it to a 160 PUMP mm discharge pipe. At A in the 30m suction pipe, the pressure is 50 KPa. PA=50KPA At B that is 30 m above A, determine 220 mm the pressure. If the horse power applied by the pump is 30 HP., head loss equal to 2 m.
Q2. Water Is flowlng downwards in the arrangement shown in figure below at a flow-rate of 0.4 m/s. What must be the value of d for the two pressure gauges to show the same reading? Assume energy loss is insignificant. diameter 300 mm 3 m Diameter d
A pump draws 24 liters per second of water from reservoir Cand lifts it to reservoir D as shown in the figure. The head lost from C to 1 is 3 times the velocity head in the 150-mm suction line and the head lost from 2 to D is 25 times the velocity head in the 100-mm discharge line. El, 210 m Figure 402 * Et Om El. -20 m 150 nm PLIMP What is the pressure head at point 1 in meters of water? 16.58 O 23,56 19.62 O 32.67
The large tank shown in the figure contains water and shoots it up using a pump connected to its outlet. Which of the following statements is FALSE? 27 m 20 m O a. The pump head is equal to 27 m O b. The elevation head difference between the water surface in the tank and the highest point of the water jet is 7 m O c. The pressure head at the surface of the tank is zero O d. The velocity head at the highest point of the water jet is zero
A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%)a) If the tap on the output pipe is closed (i.e. R = ∞) determine how long it will take the tank to fillup assuming qi = 0.001 m3/s.b) If the tap on the output is open liquid will be coming out at the same time as liquid is going in. Ifthe flow rate in is bigger than flow rate out the height of the liquid in the tank will rise. Using theR value given on the Results Sheet, determine the steady state height of liquid in the tankassuming qi = 0.001 m3/s.c) In theory it will take an infinite amount of time to achieve steady state so in practice we define thetime to respond as the 95% settling time (i.e. the time taken to get to within 5% of the steady stateoutput.) Measure the 95% settling time from your simulation in Q1b). 2. Emptying the tank (10%)a) Assuming the tank is initially full (i.e. h(0) = hmax) and the input is turned off (i.e. qi = 0) the tank willstart to empty. Assuming the R value in Q1b), determine the time…
Calculate the discharge through a pipe of diame ter 200 mm when the difference of pressure head between the two ends of a pipe 500 m apart is 4 m of water. Take the value of 'f' = 0.009 %3D
A liquid (SG = 0.626) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -7 psi and 44 psi, respectively. The rate of flow in the pipe is 0.589 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 88%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 7 ft. Use 1 hp = 550 Ib-ft/s. Round off to two decimal places. Pipe Diameter, D y Pump Liquid Specific Gravity, SG
(4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 °C. The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is 0. 07 L / D) V? H. D=20 cm, the rate of flow is 0.0 a=1 ase calculate the 2g pressure in the pipe. Elevation = 100 m Elevation = 20 m L=2000 m %3D II ||
4. The pressure intensity at a point in a fluid is given 4.9 N/cm². Find the corresponding height of fluid when it 5. An oil of sp. gr. 0.8 is contained in a vessel. At a point the height of oil is 20 m. Find the corresponding m [Ans. (a) 5 m of water, (b) 6.25 m of cil is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) and pbove it an oil of sp. gr. 0.8 for a depth of 2 m height of water at that point.