In the case of Brayton cycle with regeneration, I. the regenerator can not be used when the temperature of compressed air is more than the temperature of exhaust gases from the turbine. II. the efficiency of the Brayton cycle with regeneration is always greater than the efficiency of the simple Brayton cycle. O a. Only II is true O b. I and II are true Oc Only I is true O d. I and II are false

In the case of Brayton cycle with regeneration, I. the regenerator can not be used when the temperature of compressed air is more than the temperature of exhaust gases from the turbine. II. the efficiency of the Brayton cycle with regeneration is always greater than the efficiency of the simple Brayton cycle. O a. Only II is true O b. I and II are true Oc Only I is true O d. I and II are false

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the case of Reheat Rankine cycle I. the work output is always more than simple Rankine cycle. II. the quality of steam at the end of expansion is always less than that of simple Rankine cycle. a. land Il are false O b. Only I is true O c. Only Il is true O d. land Il are true
5.)(II) The idealized air-standard Diesel cycle is shown in Fig. 21.26. Air enters the combustion chamber in an intake stroke (not shown). It is adiabatically compressed from a to b. At b fuel enters the system and starts to burn, essentially at constant pressure. This process continues until point c, when the gas expands adiabatically to point d. This is the power stroke. In the exhaust stroke, the combustion prod- ucts cool at constant volume from d back to the initial point a. Show that the efficiency is 1 (Ta- Ta y Te Th e = 1. 1-4 - FIGURE 21.26 Problem 5 V
B-Correct the wrong sentence: 1. Adiabatic compression is the most desirable process to get minimum work in the compressor. 2. The thermal efficiency of constant pressure cycle is depends on the compression ratio 3. The most important fuel elements are carbon and ash. 4. The pressure of a mixture of gases is equal to the sum of partial masses of the constituents. 5. The Rankine cycle is the most efficient cycle
17. A diesel engine working on an air standard cycle has a peak temperature of 1200K. If the compression ratio of the engine is 20 and that the air at the entrance condition has a temperature of 300C. Determine the efficiency of the cycle. a. 68.6990% b. 68.6998% c. 68.6989% d. 68.6986%
Part 2 Discuss the following related to the principles of operation for a gas turbine power plant A. What is the difference between closed and open gas turbine cycle. B. C. Explain how a closed gas turbine engine can be combined with a Rankine cycle. Why Brayton cycle is more preferred compared to Rankin cycle in power plant stations? D. How would you increase the efficiency of a Brayton cycle?. How would you minimize the back work ratio in a Brayton cycle?. E.
1. What is the specific enthalpy at the outlet of the turbine and compressor in KJ/Kg 2.what is the power output per unit mass flow rate of air of the turbine . 3.what is the rate of heat input per unit mass flow rate of the air during the heat addition process
Consider the operation of the ideal Brayton cycle with a regenerator. The maximum temperature in the cycle is set. What happens with increasing pressure ratio? Group of answer choices The amount of heat added in the cycle up to a point will decrease with net work output remaining the same and thermal efficiency will increase. Thermal efficiency will increase Compressor exit temperature will increase with turbine exit temperature remaining the same. When the two temperatures are equal, the benefit of the regenerator will be zero. Thermal efficiency will decrease
please provide full solution
Please draw the TS diagrams of the cycle. Subject: Thermodynamics (Rankine Cycle)
A Joule cycle is used for electricity production in a power plant. Air is introduced to the cycle from the ambient with a pressure of 1 bar, and a temperature of 20 °C. The air is compressed in compressor C1 and is thereafter cooled down to 30 °C. The air is compressed again in compressor C2. The air passes through a regenerator where it is heated by exhaust gases. Heat is added by combustion of fuel in combustion chamber CC1. The air is thereafter expanded in turbine T1. The air is reheated in combustion chamber CC2. The air is expanded in turbine T2, and the exhaust gases after the turbine pass through the regenerator and is finally vented to the ambient. Turbine T2 is driving compressor C2. The net work from the cycle is produced by the difference between the work produced by turbine T1 and compressor C1. The regenerator efficiency is 0.80, the isentropic efficiency of the compressor is 0.83, and for the turbine 0.85. The temperature after CC1 and CC2 is tCC, the pressure after…