Brayton cycle used for gas turbine in aircraft consists of the following operations in sequence, O a. Isentropic compression, isobaric heat supply, isobaric expansion O b. isentropic compression, isobaric heat supply, isentropic expansion. C. Isentropic compression, isentropic heat supply, isobaric expansion d. Isentropic compression, isobaric heat supply, isochoric expansion

Brayton cycle used for gas turbine in aircraft consists of the following operations in sequence, O a. Isentropic compression, isobaric heat supply, isobaric expansion O b. isentropic compression, isobaric heat supply, isentropic expansion. C. Isentropic compression, isentropic heat supply, isobaric expansion d. Isentropic compression, isobaric heat supply, isochoric expansion

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.)(II) The idealized air-standard Diesel cycle is shown in Fig. 21.26. Air enters the combustion chamber in an intake stroke (not shown). It is adiabatically compressed from a to b. At b fuel enters the system and starts to burn, essentially at constant pressure. This process continues until point c, when the gas expands adiabatically to point d. This is the power stroke. In the exhaust stroke, the combustion prod- ucts cool at constant volume from d back to the initial point a. Show that the efficiency is 1 (Ta- Ta y Te Th e = 1. 1-4 - FIGURE 21.26 Problem 5 V
Consider a modification of the cold air-standard Otto cycle in which the isentropic compression and expansion processes are each replaced with polytropic processes having n = 1.3. The compression ratio is 12 for the modified cycle. At the beginning of compression, p1 = 1 bar and T1 = 300 K and V1 = 2270 cm3. The maximum temperature during the cycle is 2000 K. Determine the thermal eficiency, for the modified cycle. A) 49.77 B) 58.48 C) 52.51 (D) 48.27
c) In an air standard diesel cycle, the pressure and volume of beginning of compression are 200 kPa and 0.05 m respectively. Pressure after isentropic compression is 5.2 MPa and isentropic expansion is 400 kPa. Determine compression ratio, cut-off ratio, expansion ratio, cycle efficiency.
B-Correct the wrong sentence: 1. Adiabatic compression is the most desirable process to get minimum work in the compressor. 2. The thermal efficiency of constant pressure cycle is depends on the compression ratio 3. The most important fuel elements are carbon and ash. 4. The pressure of a mixture of gases is equal to the sum of partial masses of the constituents. 5. The Rankine cycle is the most efficient cycle
7.
Part 2 Discuss the following related to the principles of operation for a gas turbine power plant A. What is the difference between closed and open gas turbine cycle. B. C. Explain how a closed gas turbine engine can be combined with a Rankine cycle. Why Brayton cycle is more preferred compared to Rankin cycle in power plant stations? D. How would you increase the efficiency of a Brayton cycle?. How would you minimize the back work ratio in a Brayton cycle?. E.
Thermodynamics 2
Which of the following statement is not true of the diesel cycle? (you must use thermodynamic diagram with explanation.)a. The expansion process is an isentropic process.b. The exhaust process is a constant-volume process.c. The combustion process is a constant-volume process.d. The compression process is an adiabatic process.e. One heat transfer process is a constant-pressure process
Chose the correct anser 7. The efficiency of Carnot cycle depends upon a. temperature limits b. pressure ratio c. volume compression ratio d. cut-off ratio and compression ratio 8. The compression ratio is the ratio of a. swept volume to total volume b. total volume to swept volume c. swept volume to clearance volume d. total volume to clearance volume 9. The ratio of isothermal power to actual measured input power of a compressor is known as: a. Isothermal efficiency b. Volumetric Efficiency c. Barometric efficiency d. None 10. The part use for heat rejection in the Rankine Cycle is: a. Turbine b. Boiler c. d. Pump Condenser
@clean solution
ı need solution
Assume a basic (non-regenerative) ideal Brayton cycle where air modeled as IG with variables specific heat. The gas-turbine engine has the following operational parameters: Inlet Air Temperature:537 R Inlet Air Pressure:14.696 psia Compressor Pressure Ratio (rp):6.0 Firing Temperature:2400 R Heat Recovery Steam Generator: Assume that the exhaust from the gas turbine engine is directed to a heat recovery steam generator (HRSG)to produce wet steam (i.e. saturated vapor) at a pressure of 600 psia. Liquid water is supplied to the HRSG at 100F and 600 psia. The exhaust gas from the gas-turbine engine leaves the HRSG at the saturation temperature of the wet steam. With these conditions determine: a) the exit temperature of the wet steam (F), b) the intensive steam production rate, lbm-steam/lbm-exhaust gas. Absorption Chiller CHP: Assume the process steam from the HRSG is now used to drive an absorption chiller with COP of 0.7, and that the mechanical power of the gas-turbine engine is used…