6) In cooling tower below, derive the given equations based on the systemboundary below (neglect fan/pump work).Air Out2Water SprayedAir Inma1Make-up watermMMma↑aintaintAir Blows Upwardmm = ma (W2 - W1)BAWarm WaterGondenserPumpmwmw00000Cold Waterma ( W2- W1 ) hm + mw (hB-hA) =ma (h2-h1)

Given Data - The cooling tower -A cooling tower is a special type of heat exchanger in which the…

In cooling tower below, derive the given equations based on the system boundary below (neglect fan/pump work). Vater Sprayed Air In ma Make-up watèr mM M Air Out 2 ma Taintain Aiir Air Blows Upward mm = ma (W2 - W1) B A Warm Water Gondenser Pump mw mw 00000 Cold Water ma ( W2 - W1 ) hm + mw (hB-ha) = ma (h2-h1)

In cooling tower below, derive the given equations based on the system boundary below (neglect fan/pump work). Vater Sprayed Air In ma Make-up watèr mM M Air Out 2 ma Taintain Aiir Air Blows Upward mm = ma (W2 - W1) B A Warm Water Gondenser Pump mw mw 00000 Cold Water ma ( W2 - W1 ) hm + mw (hB-ha) = ma (h2-h1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

V1
A pump is working on these parameters 0.56 me/s with TDH of 63 meters. The pump efficiency is at 0.94% and the motor efficiency is at 0,89 %. What is the brake power in kW? Make your answer in whole number and choose the next whole number, say for example 25.2 kW it should be 26 kW.
8
Q2: The motion speed of the piston in one hydraulic transmission system is depend on the inlet flow rate, if gw=50ml/s, the surface of the cylinder is 5 cm², so what's the speed of the piston?
QUESTION 3Discuss the five characteristics of a System.
FROM BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
Q3: For building in the city of Nassiriah, it is given that: Room sensible heat gain = 40 KW = 10 KW Room latent heat gain Inside design condition: 1- Apparatus dew point temperature. 2-Condition of air leaving cooling coil. 3- Ventilation air mass and volume flow rate. 4- Total cooling load of the conditioning plant. FTP لاطول مار 25 DBT, 50 % RH Outdoor design condition: 43 DBT and 27.5 WBT Bypass factor of the cooling coil = 0.1 Seta The return air from the space is mixed with the outside air before entering the cooling coil in the ratio of 4/ by weight. 도 Determine: SHYLH h₂-hy Ess=fre-pdo 4₂-4.
Q5: A liquid-level system has a cross-sectional area of 3.0 ft². The valve characteristics are q = 8 h Where: q = flow rate cfm, h = level above the valve, ft Calculate: a) The time constant for this system. b) The time constant for this system at q = 8√h
PROBLEM #5 SoNe for the masimum Compressi ve load: weight ratio 6f each pole Given: a) Concree pole (rectangular) dimensions of each unit : 30.m x 30 cm rectangular pole haximum compressive Streng th: 45 Mpa Mass lo00 kg ニ 6) Giant bamboo pole Chollow cyinder) outside diameter diameter 30 cm - 22 cm maxi mum compressive st reng th : Bo mpa inside mass :100 Rg pae (hollow cylinder) outs ide diameter = 30 cm C. Steel inside di ameter = 28 cm marimum compressi ve streng th = 200 mpa CO mass = 25o kg di) Wood Caylindrical, not hollow diameter = 30 cm markimum streng th- 1 mpa compressive Kg mass = 350 %3D
Q.10 Reynolds number is the ratio of inertial force to: A Gravitational force В Surface tension C Elasticity D Viscous force
Asap please
1. A centrifugal fan is delivering 2000 cfm of air at a total pressure differential of 2 in.w. The fan has an outlet area of 0.85 ft? and requires 1.25 hp shaft input power. The fan speed is 1000 rpm. If the fan motor efficiency 85%, calculate: a) The total fan output power (hp) b) The fan total efficiency c) The fan static pressure, in.w d) The fan static efficiency e) The motor power, kW f) If the fan speed is reduced to 800 rpm, compute; i. The capacity (cfm) ii. The static ant total pressures, in.w. ii. The required power (shaft power), hp