in a vertical pipe conveying oil of specific gravity 0.8, two pressure gauges have Problem been installed at A and B where the diametres are 16 cm and 8 cm respectively. A is 2 metres above B. The pressure gauge readings have shown that the pressure at B is greater than at A by 0.981 N/ cm². Neglecting all losses, calculate the flow rate. If the gauges at A and B are replaced by tubes filled with the same liquid and connected to a U-tube containing mercury, calculate the difference of Lauel of wareu iu the two limbs of the U.tube

in a vertical pipe conveying oil of specific gravity 0.8, two pressure gauges have Problem been installed at A and B where the diametres are 16 cm and 8 cm respectively. A is 2 metres above B. The pressure gauge readings have shown that the pressure at B is greater than at A by 0.981 N/ cm². Neglecting all losses, calculate the flow rate. If the gauges at A and B are replaced by tubes filled with the same liquid and connected to a U-tube containing mercury, calculate the difference of Lauel of wareu iu the two limbs of the U.tube

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
Q2. Oil with an absolute viscosity of 0.125 N.s/m² and a density of 890 kg/m' is flowing in a 16.5 cm diameter pipe at a 7.5 L/s flow rate. • The fully developed flow is expected to start after.. ... m of pipe entrance.. • plot the shear stress within the pipe cross section.
A valve is suddenly closed in a 200 mmø pipe. The increase in pressure is 700 kPa. Assuming that the pipe is rigid and the bulk modulus of water is 2.07 x 109 N/m2 If the length of the pipe is 650 m. long, compute the water hammer pressure in kPa at the valve if it is closed in 3 sec.
Question 1. Water flows with a discharge of 0,020 through a SG pipe reducer as is shown in the Figure 1. The static pressures at 1st (Di=0,31 m) and 2nd (D2=0,18 m)cross-sections are measured by the inverted U- D2 tube manometer containing oil of specific gravity, SG as 0,7. Determine the manometer reading, h *(m). (1) Water Figure 1
Estimate the maximum water hammer pressure generated in a rigid pipe of a 3 m dia pipe with an initial velocity of 3.0 ms-¹ and the pipe is 8 km long. The downstream valve at the pipe end is closed in 4 seconds. The bulk modulus of water is 2.25x106 kPa and the mass density is 995.7 kg/m³. Also determine the critical time of closure.
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
Two pipes namely A and B are connected by manometer (SHg = 13.6). The fluid in both pipes is an oil with r.d of 0,923, indicates a differential pressure reading h of 0.3 m. If the pressure in pipe A increases by 6 kPa, while the pressure in pipe B decreases by 2 kPa, determine the new differential pressure reading h of the manometer. Neglect the diameter of the pipes. mercury 0.1 m D 01 m Mercury
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
Oil of viscosity 0.1 Pa.s and specific gravity 0.90, flows through a horizontal pipe of 25 mm diameter. If the pressure drop per meter length of the pipe is 12 kPa, determine (a) the rate of flow in N/min; (b) the shear stress at the pipe wall; (c) the Reynolds number of the flow; and (d) the power required in W per 50 m length of pipe to maintain the flow. [Take: unit weight of water = 9810 N/m³]