In a particular material, if the modulus ofrigidity is equal to the bulk modulus, thePoisson Ratio would be:(a) 1/8(c) 1/2(b) 1/4(d) 1

Answered: Image /qna-images/answer/0e68bd17-0723-4b1f-8f0a-059726a40459.jpg

Answered: In a particular material, if the…

In a particular material, if the modulus o rigidity is equal to the bulk modulus, th Poisson Ratio would be: (b) 1/4 (a) 1/8 (c) 1/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q- If the Poisson's ratio of an elastic material is 0.25, then find the ratio of modulus of rigidity…

A: Poisson's ratio=0.25, It is needed to find the ratio of the modulus of rigidity and Young's…

Q: Table 1 shows the stress-strain data for a new polymeric material rod subjected to an axial load.…

A: Table shows the stress strain data for a new polymeric material rod subjected to an axial load .Now…

Q: A steel column has a sectional area of 0.126 m^2 and a length of 3 m. IF a 50000 KN load is applied…

A: Given data, Column sectional area A = 0.126 m^2 Column length L = 3 m Force applied F = 50000 kN =…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 780 mm.…

Q: polymer a bending moment M. zth of the eam Is L dimensions of the beam are b, = 33 mm, di = 102 mm,…

A: It is asked to calculate maximum moment (M) that can be applied.

Q: 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Stress, psi

A: The given stress-strain graph of aluminum alloy is-

Q: A 0.375 -in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and B. The…

A: Given data in question Load 11 kips Thick 0.375 inch Height 3 inch Strain in longitudinal and…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: A piece of (A =53 mm × B= 29 mm) material experiences a homogenous deformation. The deformed shape…

Q: A cylinder of outer radius R₂=100 mm is fitted on another cylinder of outside radius R₁=85 mm with…

A: Given values: R2 = 100 mm R1 = 85 mm t = 30 mm Hoop stress = 90 MPa E = 105 MPa ν=0.15

Q: 3- Bending strength of a construction material is 105 MPa. The porosity of this material is 5% and…

A: Relation between Bending strength and porosity is given in the question. We will use this relation…

Q: Data taken from a stress-strain test for a brittle alloy are given in the table. The curve is linear…

A: , ksi, in/in0034.30.000843.50.001347.00.001749.00.002149.50.0023The rupture stress,

Q: A piece of 50 mm × 30 mm material experiences a homogenous deformation as shown in the figure below.…

Q: b) Figure Q1 shows ceramic specimens subjected to the pure uniaxial force. Specimen A is compressed…

A: An elemental area can be subjected to stress due to applied load . For uniaxial it is subjected to…

Q: Creep exercises You are involved in a design for high temperature alloys and have performed a…

A: Solution:- Give data:- To know:- Selection of material as shown in above figure.

Q: For a material, the modulus of rigidity is 100 GPa and the modulus of elasticity is 250 GPa. The…

A: Given data : Modulus of elasticity (E)=250 GPaModulus of rigidty (G)=100 GPa

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: Q- If the Poisson's ratio of an elastic material is 0.25, then find the ratio of modulus of rigidity…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…

Q: 2) For a specific material having poisson's ratio -0.32, the percent of elastic modulus to modulus…

Q: An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod s subjected to a…

Q: The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity…

Q: 1: For a material stress at proportionality limit is 400 MPa and modulus of elasticity is 200 MPa.…

Q: A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in…

A: P=24kN

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Given : Length of layer AB and CD, L = 270 mmIncrease in layer AB, ∆AB = 40×10-3 mmDecrease in layer…

Q: If Poisson's ratio is 0.42, the Modulus of rigidity is 70.4225 GPa, and the bulk modulus is 416.66…

Q: len A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T)…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm.…

A: Determine the largest moment M that can be applied as shown to the beam.

Q: The state of stresses in the x and y directions at a point in a given material is shown in the fig…

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

A: To determine the horizontal deflection of end C relative to end A. Given, Area of bar (1), A1 =…

Q: The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

Q: An extruded polymer beam is subjected toa bending moment M. The length of the beam is L = 500 mm.…

Q: (a) What is the permanent set of the bar (in mm)? 2.184 ] mm (b) If the bar is reloaded, what is the…

A: Given that, length of bar = 390 mm elongation = 2.34 mm Therefore, strain, ε=ΔLL=2.34390=6×10-3…

Q: All of the following statements are correct except: a. Materials with higher modulus of elasticity,…

Question

In a particular material, if the modulus of
rigidity is equal to the bulk modulus, the
Poisson Ratio would be:
(a) 1/8
(c) 1/2
(b) 1/4
(d) 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For material, the modulus of rigidity is 100 GPa and the modulus of elasticity is 250 GPa. The value of the Poisson's ratio is
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
In a tensile test on a metal specimen having a cross section 20 mm by 10 mm elastic breakdown occurred at a load of 70 000 N. A thin plate madec from the same material is to be subjected to loading such that at a certain point in the plate the stresses are o,=-70 N/mm², 7.y= 60 N/mm² and o. Determine the maximum allowable values of o, using the Tresca and von Mises theories of elastic breakdown. Ans. 259 N/mm² (Tresca), 294 N/mm² (von Mises).
L=2.75
1 The principal stresses at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and μ = 0.3. What would be the value of o at failure when computed by different theories of failure.
Give me right solution with clear hand writing.
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
If the posson ratio of elastic material is 0.453 the ratio of modulus of rigidity to Young modulus
Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam areb1 = 35 mm, d1= 115 mm, b2= 21 mm, d2 = 21 mm, and a =7 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be %3D %3D %3D %3D %3D %3D applied as shown to the beam. b2 a 不 d2 d1 b1 Answer: N-m M% =
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
Answer in two decimal places please