In a machining setup, workpiece B, which weighs 10.5 lb, is supported by a fixed V block E and a clamp at A. All contact surfaces are frictionless, and the clamp applies a vertical force of 16 lb to the workplece. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 30° 30° Draw the free-body diagram needed to determine the reactions at points Cand D between the block and the workplece. The free-body diagram of the workplece is

In a machining setup, workpiece B, which weighs 10.5 lb, is supported by a fixed V block E and a clamp at A. All contact surfaces are frictionless, and the clamp applies a vertical force of 16 lb to the workplece. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 30° 30° Draw the free-body diagram needed to determine the reactions at points Cand D between the block and the workplece. The free-body diagram of the workplece is

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.1: Cnc Basics

Problem 3RQ: Briefly describe a ball screw and a linear guide.

See similar textbooks

Similar questions

Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt.The operation is to be started usign a push button. An acknowledgement signal is required when the piston is fully extended. to ensure that the work piece has been tipped onto the belt.The return stroke is to be automatic. Answer using the Solution form provided in the uploaded image.
Off Center Pick 2(m x G xd) F = √(b²x p²) FT = FXaGX Sf μ Center Pick F=WXG 101 F N =- μ A part weighing 15 lbs. is going to be picked up with a parallel jaw gripper. The grip surface is 2.25 inches from the center of gravity with a gripping surface of 1.625 inches and a coefficient of friction of .95. The width of the part is 3.25 inches. It will have a maximum acceleration of 3.25Gs and a safety factor of 2 must be maintained. Find the force required to hold this part. Q Search Payload Calculation Ap = P - Wt 40 + 9 신
Please solve ellaborately using the equation provided in the figure and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You. Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
A mechanism to spray water onto vehicles at an automated car wash is shown. Classify the four-bar mechanism, based on its possible motion, when the lengths of the links are: a = 12 in b = 1.5 in C = 14 in d = 4 in Complete solution must be included in the file that will be uploaded at the end of assessment. Input the category type of the given four-bar mechanism in the space provided. For example, "DOUBLE CRANK" or "CRANK-ROCKER" etc. (refer to MODULE 1 for the table with the list of different categories.)
Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You! Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a crossbelt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250,and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diametersof all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.
An automatic door lock system is to be designed for automatically locking/unlocking car doors. The design will utilize an electric solenoid with sufficient force and stroke to provide the necessary motion. If the force required to drive the lock linkage is 9.5 N, determine if the solenoid with the following specifications meets this requirement: Number of turns Current Air gap Plunger dia, 2500 1.0 Amps 10 mm 18 mm The initial force available from a solenoid F P=2(ND)² HA 82
What weight (kg) can be lifted by a double threaded screw that has an efficiency of 85% if it is opetated by a 52 lb force at the end of a 25 inches lever ?The pitch of the screw is 0.55 inches
Item 1 used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 4.5 in and is rotating about point O, which is offset from the center by a distance c = 3.0 in. The cam's angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. (Figure 1) Figure (0,0 36°F Clear r W 1 of 1 Par Find align Expr Vie Omin Subn Provide Feedb
A bolt with a square threaded screw has mean diameter of 25 mm and a pitch of 3 mm. It carries an axial thrust of 10 kN on the bolt head of 25 mm mean radius. If u = 0.12, find the force required at the end of a spanner 450 mm long, in tightening up the bolt. 3. [Ans. 110.8 N] A turn buckle with right and left hand threads is used to counle twvo railway coaches The threads
89cN of force is applied to the end of 0.7m long crowbar at a 80 degree angle. Calculate the torque.
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B