An automatic door lock system is to be designed for automatically locking/unlocking car doors. The design will utilize an electric solenoid with sufficient force and stroke to provide the necessary motion. If the force required to drive the lock linkage is 9.5 N, determine if the solenoid with the following specifications meets this requirement:

An automatic door lock system is to be designed for automatically locking/unlocking car doors. The design will utilize an electric solenoid with sufficient force and stroke to provide the necessary motion. If the force required to drive the lock linkage is 9.5 N, determine if the solenoid with the following specifications meets this requirement:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For nos. 21-23, satisfy the conditions of the given problem below: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear as shown in the figure 1. Determine: 21. the force in the strut AB. * 1 point 30° 450 lb. 1350 lb O A. 215.3 lb B. 224.4 lb C. 233. 2 lb D. 234.3 lb 1 ft 2 ft
For nos. 21-23, satisfy the conditions of the given problem below: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear as shown in the figure 1. Determine: 21. the force in the strut AB. * 1 ft -20% 2 ft 1350 lb 30% 450 lb. A. 215.3 lb B.224.4 lb C. 233, 2 lb D. 234.3 lb Option 5 22. the horizontal component at the pin C. * A. 628.6 lb B. 627.8 lb C. 634.4 lb D. 652.3 lb 23. the vertical component at the pin C. A. 1468 lb B. 1485 lb C. 1500 lb D. 1526 lb
Q2: The figure below shows 3 fiange coupling bawce. low hydro urbine and. generato:r. The generator delivers power cf 10 HP and speed of 1500 rpm. Design the shafts, couplirg, keys & bolts. bearing runner seal bearing bex bsaring couring generater Key Suát Boit
Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
Torque required for achieving the tighting force
Necessary torque to tighten the M12 bolt 400 kgcm, wrench size 18 cm, the lever force to be applied to the key and the tightening force of the bolt. find?
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
+ Frictional Forces on Flat Belts When engineers design belt drives and band brakes, they engineer them to withstand the frictional forces that develop between the belts or bands and their contacting surfaces. These frictional forces lead to tensions on each side of the contacting surfaces that are unequal; the segment aligning with the motion of the belt or band has a greater tension. Figure B 0.500 m 0.200 m -0.400 m- A 3 of 3 0.300 m Part C mc= Block A has a mass of mA = 49.0 kg and rests on a flat surface. (Figure 3)The coefficient of static friction between the block and the surface is A = 0.300. The coefficient of static friction between the rope and the fixed peg B is 0.320. The width of the block is d = 0.250 m. Find the greatest mass, mc, that weight C can have such that block A does not move. Express your answer numerically in kilograms to three significant figures. ▸ View Available Hint(s) Submit Drouide Foodbook VAZO I vec ? 1 of 3 kg > Review
The driving shaft of a Hool joint rotates at a uniform sp. of 400 rpm. If the maxim variation in speed of the dri shaft is + 5% of the mean speed, determ the greatest permissible angle between axes of the shafts. What are the maxim and the minimum speeds of the driven sho
Item 1 used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 4.5 in and is rotating about point O, which is offset from the center by a distance c = 3.0 in. The cam's angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. (Figure 1) Figure (0,0 36°F Clear r W 1 of 1 Par Find align Expr Vie Omin Subn Provide Feedb
(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor=1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter = 500 mm Coefficient of friction for motor pulley = 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt = 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa