In a given T-Beam, flange width = 700 mm, slab thickness = 100 mm, thickness = 350 mm, effective depth = 450 mm. It is singly reinforced at the bottom side (tension side) with As = 2700 sq. mm. Take fc' = 17.24 MPa, fy = 413.7 mm. %3D web %3D %3D b) Determine the value of "Mu" 387.921 kN-m 415.498 kN-m O None of the Choices 406.475 kN-m O 397.282 kN-m O 424.353 kN-m

In a given T-Beam, flange width = 700 mm, slab thickness = 100 mm, thickness = 350 mm, effective depth = 450 mm. It is singly reinforced at the bottom side (tension side) with As = 2700 sq. mm. Take fc' = 17.24 MPa, fy = 413.7 mm. %3D web %3D %3D b) Determine the value of "Mu" 387.921 kN-m 415.498 kN-m O None of the Choices 406.475 kN-m O 397.282 kN-m O 424.353 kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the reinforcement of the cantilevered slab (CS – 1) in Figure 3. The slab is to be used for terrace occupancy with a designed floor live load of 4.80 kPa. Use 12mm dia deformed bars as main reinforcement and 10mm dia bars for temperature reinforcement. Also, use fc’ = 20.7 MPa and fy = 276 MPa. Draw the structural details of the slab.
Hi.Please help me with this one. Subject: Strength of Materials
2. The beam shown is prestressed using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons fpy = 1350 MPa, and fc' = 35 MPa. The area of prestressed reinforcement in tension zone Aps = 1000 mm². The specified yield strength of prestressing tendons fpy = 1160 MPa. 0.85fc' C a 430 N.A. |(d-a/2) Ap=1000 T=Ap,Sps 250 a. Determine the value of the stress in prestressed reinforcement at nominal strength. b. Determine the value of the depth of the compression block. c. Which of the following gives the ultimate moment capacity of the prestressed beam.
Compute the flexural stress (MPa) in the steel for the beam shown using transformed-area method. Area of 1-#29 bar is 645mm?. Assume cracked section. 530 mm 600 mm M = 130 kN-m n = 9 4 #29 70 mm - 350 mm
A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 42 kN/m, LAB = 1.5 m, Lgc = 3.0m, and Lco = 1.5 m. %3D Consider the entire 6.0 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). B LAB LBC LCD WT305 x 41 Answer: (a) OmaxT MPа (b) omaxc МPа
So= 0.005 6 ft M = 0.015 5ft FIND Q 2 ft 2/3/2 -1.486 AR S, Prtm = 14.7 pora CROSS - SECTION
Dont round off initial values, round off final ans only pls
1. For the given singly reinforced beam section, fy =352 MPa, and f's = 28MPA. Calculate the required parameters for the different section condition in the table. d = 257mm h = 307mm 200mm Concrete Steel of Location Limit for No. of 16mm Area of diameter bar Condition Depth strain strain compression of block "a". neutral steel in to meet the axis "c". sq.mm. given beam condition. Units N/A N/A mm mm Sq.mm bars Balanced 0.003 Condition Compression 0.003 controlled Transition 0.003 controlled Tension 0.003 controlled
This is civil engineering. Everything needed is provided. Please answer all parts to the best of your ability. Provide thorough answer and explanation.
Determine the required steel area for a T-beam that traverses the center of a floor system for which bw = 300 mm and d = 550 mm. The beams are 4.8 m long and spaced at 3 m. O.C. The slab thickness is 100 mm. Mp = 400 KN-m (including its own weight), ML = 500 KN-m. f'c = 28 MPa, and fy = 414 MPa
PLEASE INCLUDE COMPLETE FIGURES
A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc=50mm, stirrups= 10mm, fc'=21Mpa and fy=415Mpa. Calculate the strength reduction factor a. 0.65 b. 0.651 c. 0.67 d. 0.809 e. 0.90