In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 5 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 156.46, 199.62, 189.31, 102.22, and112.09 respectively. In the same sample, the corresponding ranges are: 11.97, 12.17, 13.94, 11.86, and 11.83 respectively. What are the lower and upper control limits for the X-bar chart?

In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 5 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 156.46, 199.62, 189.31, 102.22, and112.09 respectively. In the same sample, the corresponding ranges are: 11.97, 12.17, 13.94, 11.86, and 11.83 respectively. What are the lower and upper control limits for the X-bar chart?

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Aspen Plastics produces plastic bottles to customer order.The quality inspector randomly selects four bottles fromthe bottle machine and measures the outside diameter ofthe bottle neck, a critical quality dimension that determineswhether the bottle cap will fit properly. The dimensions(inch) from the last six samples are Assume that only these six samples are sufficient, and use thedata to determine control limits for an R- and an x-chart.
What does a run of 5 points above or below the centerline in a control chart imply?
A microbrewery tracks its output in gallons over a five hour period for each of seven days. Their data is in the table below, and they went ahead and calculated the averages and ranges for the individual samples and the overall averages Their data and the factors tables can be found below. Calculate the upper (LCL) and lower (UCL) control limits for X bar, and R charts for their process. Day (X values) X̅ R 1 46 49 45 47 48 47.0 4 2 43 52 46 52 44 47.4 9 3 45 55 46 51 43 48.0 12 4 39 44 42 43 40 41.6 5 5 45 50 48 50 42 47.0 8 6 44 48 45 45 40 44.4 8 7 41 44 52 50 47 46.8 11 X̿ = 46.03 R̅ 8.14 Xbar chart - LCL = 40.48, UCL=46.25, R chart LCL=0, UCL=14.01 Xbar chart - LCL = 44.21, UCL=48.41, R chart LCL=0.49, UCL=17.18 Xbar chart - LCL = 42.61, UCL=49.45, R chart LCL=0.65, UCL=15.63 Xbar chart - LCL = 44.21, UCL=51.62, R chart LCL=0, UCL=17.18 Xbar chart - LCL = 41.31, UCL=50.75, R chart LCL=0, UCL=17.18
Refer to Table 56.1-Factors for Computing Control Chart Limits.(3.sigma) for this problem. Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? mm (round your response to two decimal places). b) What is the value of R? R=mm (round your response to two decimal places). c) What are the UCL, and LCL; using 3-sigma? Day 1 2 3 4 5 Upper Control Limit (UCL;)mm (round your response to two decimal places) Lower Control Limit (LCL;)mm (round your response to two decimal places). d) What are the UCL and LCL using 3-sigma? Upper Control Limit (UCLR)-mm (round your response to two decimal places). Lower Control Limit (LCL)-mm (round your response to two decimal places) Mean x (mm) 154.9 151.2 155.6 155.5 154.6 Range R (mm) 4.4 4.8 4.3 5.0 4.7 Next
Cartons of Plaster are supposed to weigh exactly 32 ounces. Inspectors want to develop process control charts. They take five samples of six (6) boxes each and weigh them. Sample means (X-bar) are: 33.8, 34.6, 34.7, 34.1, and 34.2 respectively. Also, the corresponding ranges are: 1.1,0.3, 0.4. 0.7, and 0.3, respectively. The lower and upper control limits of the xbar-chart are respectively O a. None is correct O b. 30.11 and 40.15 O c. 34.01 and 34.55 O d. 33.12 and 34.12 O e. 37.01 and 39.23
In a research on weight of cereal dispersed into a box of cereal, a company collected m=12 sets of inside ring diameter samples with a subgroup size of n=6 , the grand mean =17.8 ounces and the average range =1.02 ounces. Determine the upper control limit for an R chart. Enter your answer to 2 decimal places.
A producer of windshields decides to monitor the material handling system used in the plant. The producer is concerned about if there are scratches that are appearing on their finished product. The best kind of control chart to use in this case is a: r chart b: x chart c: cpk chart d: P chart
54 Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.20 ounce. For a sample size of 64, the 3-sigma X chart control limits are: Upper Control Limit (UCL) = ounces (round your response to two decimal places).
snip
2- Quality Control Charts A local brewery and bottling plant wants to keep track of the bottling filling equipment's accuracy, Bottles are to be filled with exactly 16 ounces of the drink. The following is data from the bottling equipment where 5 samples of bottles filled were pulled every hour and measured for actual quantity filled. 1- Calculate the UCL, LCL and mean for the X-bar and R data 2- Draw an X-Bar chart and a R chart. 3- Is this filling process in control or out of control? Hour X-bar R 1 16.05 .20 2 16.03 3 15.96 4 15.97 16.03 16.06 15.98 16.09 15.94 16.01 5 6 7 8 9 10 @n-5: A2 = 0.58, D3 =0, D4 = 2.11 .25 .62 .58 .71 .37 .46 .21 .35 .29
< Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Sampling 4 pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has produced the following results: Hour X 1 2 3 4 5 6 R 3.25" 0.65" 3.00 1.23 3.32 1.43 3.39 1.26 3.07 1.17 2.96 0.37 Hour X R Hour R Hour 7 2.95" 0.48" 13 X 3.11" 0.90" 2.73 1.36 19 20 8 2.55 1.18 14 9 0.71 3.12 1.11 21 3.12 2.85 15 16 10 1.38 2.74 0.50 22 11 2.83 1.22 17 2.86 1.38 23 12 3.07 0.45 18 2.64 1.29 24 X 4.51" 2.89 2.65 3.18 3.04 2.54 R 1.56" 1.14 1.13 0.51 1.58 1.02 Based on the sampling done, the control limits for 3-sigma x chart are (round all intermediate calculations to three decimal places before proceeding with further calculations): Upper Control Limit (UCL) = inches (round your response to three decimal places).
A control chart for fraction nonconforming is to be established using a center line of p=0.03. What sample size is required if we wish to detect a shift in the process fraction nonconforming to 0.08 with probability 0.50? 1269 475 73 316 216 2 105 150 265