In a balanced three-phase system, the source is Y-connected, and Van = 12040° V (RMS voltage). The source feeds two loads. Load 1 is Y-connected with an impedance of 8 +j6 2/4. Load 2 is A-connected with an impedance of 6236° №/p. a) Draw the single-phase equivalent circuit. b) Calculate the line current (Ia) c) Calculate the current Iab for load 2. d) Calculate the line-to-line voltage at the load (Vab)

In a balanced three-phase system, the source is Y-connected, and Van = 12040° V (RMS voltage). The source feeds two loads. Load 1 is Y-connected with an impedance of 8 +j6 2/4. Load 2 is A-connected with an impedance of 6236° №/p. a) Draw the single-phase equivalent circuit. b) Calculate the line current (Ia) c) Calculate the current Iab for load 2. d) Calculate the line-to-line voltage at the load (Vab)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The following loads are served by a balanced three-phase source: Load 1: 18 kVA at 0.8 pf lagging Load 2: 8 kVA at 0.8 pf leading Load 3: 12 kVA at 0.75 pf lagging. Give the complex power expression for Load 3. Select one: O a. 29.80 +j13.94 O b. O c. 9.00+ j7.94 kVA 6.40 -j4.80 KVA O d. 32.90225.07° KVA O e. 14.40 +j10.80 kVA
Three-phase electricity is delivered to a factory 7 km from a distribution company. The factory receives a total of 2000 kW of power at a voltage of 10.98 kV (rms) per phase. If the transmission cable in each phase has a resistance of 1.8 per 10 km, then the total power lost in the cables of this three-phase system is (a) 4.645 W (b) 13.93 W (c) 4.645 kW (d) 13.93 kW
A load of 138+j460 Ohm is supplied through 3+j14 Ohm line as shown in Figure 1. (a) Find the average power dissipated in the line. (b) Find the value of capacitive reactance connected across the load to compensate the reactive power need of the load. (c) What is the equivalent impedance after compensation. (d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. (e) Express the power loss in (d) as a percentage of the power found in (a) j14 Figure 1 7200/0 + V (rms) Source 3 wi Line Load 138 j460
A three-phase substation bus supplies a wye and a delta connected constant impedance loads. The loads are connected in parallel. A three-phase feeder with an impedance per phase of Z = 0.6+j1.8 Q connects the loads to a source as shown in the one- line diagram of Figure below. The loads draw the following three-phase power: P1 = 35 kW S2 = 30 kVA pfi = 0.90 (leading) pf2 = 0.85 (lagging) wye connected delta connected The line-to-line load voltage is 480 V. Detemine: (a) the impedance of each load per phase, (b) the total line current flowing through the feeder, (c) the line-to-line voltage at the substation bus, and (d) the total three-phase real and reactive power supplied by the bus. Zfeed Vbus
please answer all subparts
Choose the correct answer: Capacitors in AC circuits dissipate power in the form of heat Select one: O True O False Choose the correct answer: In a balanced three-phase system, phase shift between phase and line voltage is 30". Select one: O True O False What is the phase shift between a phase current and its voltage in a three-phase balanced system? O a. 90 O b. It can be anything, it depends on system parameters. O C. 120 Od 30°
A Y-connected balanced three-phase source is connected to a three-phase balanced load through a four-wire three-phase cable. The generator has an impedance of 0.1+j0.3 Q/phase. Each phase of the cable has an impedance of 2+2j 2 The phase "B" load voltage is 102-140° kV. The impedance of each phase of the Y-connected load is 3-j5 Q/phase. For a negative sequence: 1- tto pointe) Calculate "terminal" phase voltage of phases "a" and "c" of generator. 2- E points] Calculate Vab and Vca across the load. 5 points Calculate three phase power supplied by the source. 4- 10 point] Calculate three phase power losses.
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents The answer has to be 9.3A
Phase Qz/ The eas Voltages at the terminal of abalan ced Y connected load is VAN=12o 28. Each Phase of the load consist of lo 230° .Find the active & Reactive and Complex Power Per-Phase then find the total Powers For three Phase load.
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
A 415 V, 57 Hz 3-phase supply is connected to a 3-phase star connected balanced R-L load each of resistance 13.63 ohm and impedance 65.27 ohm. Find the value of inductance in each phase. O 63.83 O 0.18 O 32.63 O 7.19