I'm looking for a conclusion based on this given result from the Falling sphere viscometer.
Q: In falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to…
A: As per given question Given data Calibration factor=0.3 Density of oil=0.8 gr/cm^3 Density of ball…
Q: Fill in the missing data A group of food technologist used a single-cylinder rotational viscometer…
A:
Q: Find kinematic viscosity of a liquid in stokes whose specific gravity is 0.95 and dynamic viscosity…
A:
Q: 1)The model of the torpedo (a military vehicle that goes very fast underwater) as placed in a tank…
A: To obtain the solution of the 1st part of the question, we will apply the Froude model law, which is…
Q: Table 1 : Setting of Question Density Dynamic Viscosity (kg/m³) Setting Centerline Velocity (m/s)…
A: given ; ⇒centerline velocity (U)=0.4m/s⇒density (ρ)=1.292kg/m3⇒dynamic viscosity…
Q: Part A The data below shows the laboratory data for a fluid obtained using a viscometer at 20°C and…
A: According to Newton's law of viscosity, the shear stress is the product of the absolute viscosity…
Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.052 poise and kinematic viscosity of…
A: Given Data: Dynamic viscosity=0.052 poise Kinematic viscosity=0.19 stokes
Q: In order to measure the blood viscosity n, we have used the below viscometer with the following…
A:
Q: For the capillary-tube viscometer shown, the liquid to be tested is drawn into the tube to the level…
A:
Q: A simple and accurate viscometer can be made from a length of capillary tubing. If the flow rate and…
A:
Q: A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in through…
A: Given Data Maximum allowable force in tape is : F=30.04 N Width of tape is : w=25.40 mm=0.0254 m…
Q: 15. Hydraulic oil with a Sg of 0.91 is pumped horizontally in a 2-in. I.D. distribution line at the…
A:
Q: In falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to…
A: Given, Density of ball = ρball = 16.6 g/cm3 Density of oil = ρoil = 0.8 g/cm3 Calibration factor = K…
Q: The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of…
A: The dimensional formula for each variable is shown below.
Q: Falling Sphere Viscometer Given: Inner diameter of cylindrical tube = 0.03 m…
A:
Q: Taylor number (Ta) is used here to describe the ratio between the inertia effect and the viscous…
A: Solution: Taylor number depends upon (i) inner radius (r) (ii) cylinder tangential velocity (v)…
Q: In the gap between the two plates, the lubricant flows in one direction (x) by the pressure…
A: Write the given data. ∆PL=25000 Pa/mB=6 mm=0.006 mμ=25×10-3 Pa·sρ=0.88 g/cm3=880 kg/m3
Q: In Bourdon Gauge experiment, if the mass of the piston is 340 gr and mass of the platform is 173 gr,…
A:
Q: You are working in a machine tool manufacturing industry for the project to design CNC control…
A:
Q: A single-cylinder rotational viscometer is used to measure a liquid with viscosity of 100 cP using a…
A:
Q: In a falling-ball viscometer, a steel ball 1.6 mm in diameter is allowed to fall freely in a heavy…
A: Given data Diameter of steel ball (d) = 1.6 mm = 1.6 * 10-3 m S.G. of oil = 0.95 weight density of…
Q: In the gap between the two plates, the lubricant flows in one direction (x) by the pressure…
A:
Q: Two indefinitely long flat plates separated by 3 inches in distance but with a thickness of 5 inches…
A: As per the our guideline we are supposed to solve only one question per post. kindly repost other…
Q: QI\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the…
A: Given that the density of the steel ball (ρb)= 8.52 gm/cm3 = 8520 kg/m3 ; Also the sp. gravity of…
Q: In Bourdon Gauge experiment, if the mass of the piston is 340 gr and mass of the platform is 173 gr,…
A: Mass of piston = 340 gr Platform mass = 173 gr Absolute pressure error = 218.9 Pa
Q: A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of…
A: As per the Bartleby rule, We’ll answer the first question since the exact one wasn’t specified.…
Q: If a certain liquid has viscosity 4.9 × 10¬³ N s/m² and kinematic viscosity 3.49 × 10' stokes, its…
A:
Q: Find the dynamic and kinematic viscosities of kerosene,
A: We need to find dynamic & kinematic viscosities of kerosene SAE 10W-30 motor oil and water (…
Q: Convert a viscosity of 61 g/(cm s) to lbf/(hr ft2). Use dimensional analysis in cancellation of…
A:
Q: As shown in Fig. 1.12, a horizontal interface 0-0 exists between two immiscible liquids. The dynamic…
A:
Q: Taylor number (Ta) is used here to describe the ratio between the inertia effect and the viscous…
A:
Q: Figure shows a gage for very low pressures, inventedin 1874 by Herbert McLeod. ( a ) Can you…
A: McLeod Gauge McLeod gauge amplifies the low pressure and was developed to extend the range of vacuum…
Q: 4. Develop the K for the relationship T = Kcp ŋ SN for the cone-and- plate rheometer; plate of…
A: Viscous force equation, F=AηVyF=Viscous force,A=Area of the moving plate,η=coefficient of…
Q: A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3…
A:
Q: Question 3 A fluid is evaluated for its viscosity using a Brookfield viscometer. Collected data of…
A: Given Collected data using a brookfield viscometer. Speed rev/min Apparent viscosity…
Q: An oil has a kinematic viscosity of 1.25 E-4 m 2 /s and aspecifi c gravity of 0.80. What is its…
A: Given data: Kinematic viscosity of the oil, ν = 1.25×10-4 m2/s. The specific gravity of the oil,…
Q: The physical model of a pipe containing water with kinematic viscosity o = 0.804 × 10-6 ™* has been…
A: (i) The kinematic viscosity of pipe (prototype) is given as, The kinematic viscosity of Model is…
Q: A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in through…
A:
Q: A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is…
A: Solution:
Q: (Dimensional Analysis) If the velocity V in a fluid flow depends on a dimension 1, the fluid density…
A:
Q: ) A simple, vertical U-tube manometer is used to measure the difference between two gas pressures.…
A: U-tube manometer contains water or mercury in a U-shaped tube and is as a rule utilized to…
Q: A tape, of width w= 25.40 mm is to be coated on both sides with a lubricant by drawing in through…
A: Given Data Width of tape is : w=25.40 mm=0.0254 m Length of tape is : L=20 mm=0.02 m Thickness is :…
Q: A cheap accelerometer, probably worth the price, can be made from a U-tube as in Fig. P2.150. If L =…
A:
Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area…
A:
Q: A viscous liquid is tested using a cone-and-plate rheometer that has a radius of 60 mm and cone…
A: A cone-and-plate rheometer is an instrument used to measure the rheological properties of fluids. It…
I'm looking for a conclusion based on this given result from the Falling sphere viscometer.
Step by step
Solved in 3 steps with 1 images
- No card B a m OO ON 95)1:45 mlms.hu.edu.jo/mod/qu P Flag question Air is contained in a piston cylinder device, it expands first isothermally (1=>2) then isobaric expansion takes place (2=>3). The processes on the T-v diagram will be: Select one: A. (1-2) Horizontal line, (2- 3) Inclined line with Positive slope. B. (1-2) Horizontal line, (2- 3) Inclined line with Negative slope. O c. (1-2) Inclined line with Positive slope, (2-3) Horizontal line. D. (1-2) Horizontal line, (2- 3) Vertical line downward. E. (1-2) Inclined line with Negative slope, (2-3) Horizontal line. F. (1-2) Horizontal line, (2- 3) Vertical line upward. ...The Reynolds number is a dimensionless group defined for a fluid flowing in a pipe as Re = Duplu where Dis pipe diameter, u is fluid velocity, p is fluid density, and u is fluid viscosity. When the value of the Reynolds number is less than about 2100, the flow is laminarthat is, the fluid flows in smooth streamlines. For Reynolds numbers above 2100, the flow is turbulent, characterized by a great deal of agitation. Liquid methyl ethylketone (MEK) flows through a pipe with an inner diameter of 2.067 inches at an average velocity of 0.48 ft/s. At the fluid temperature of 20°C the density of liquid MEK is 0.805 g/cm? and the viscosity is 0.43 centipoise [1 cP = 1.00 x 10-³ kg/(m-s)]. Without using a calculator, determine whether the flow is laminar or turbulent. Show your calculations.7. Aflat thin plate is dragged at a constant velocity of 4 m/s on the top of a 5 mm deep liquid layer of viscosity 20 centipoise. If the area of the plate is 1 m² find the drag force. Assume variation of velocity in the liquid to be linear. [Ans. 16 N]
- %AY |I1, 76% fTV s INTV Uo 10:21 یلیجرام 2.pdf Q1 1. How can recognize an extensive or intensive properties such as density, colour of gold, Volume of water in a graduated cylinder. 2. Drive the relation 1-x = Vavg - 3. A glycerin pump is powered by a 5-kW electric motor. The pressure differential between the outlet and the inlet of the pump at full load is measured to be 211 kPa. If the flow rate through the pump is 18 L/s and the changes in elevation and the flow velocity across the pump are negligible, the overall efficiency of the pump is (a) 69 percent (b) 72 percent (c) 76 percent (d) 79 percent (e) 82 percent. Q2 1. While solving a problem, a person ended up with the following equation at some stage: E 25 kJ +7 kJ/kg where E is the total energy and has the unit of kilojoules. Determine how to correct the error and discuss what may have caused it. 2. Define isolated system, specific gravity and thermal equilibrium. 3. Initially P-400 kPa and T-400 °C, as shown in FigQ2-1. What is…valg, (21535mm 1.15 The pressure difference, Ap, across a partial blockage in an artery (called a stenosis) is approximated by the equation μV Ap - K. 4 + K.(A-1) pv² = K₂ A s.r to zogy nish190 32\V as bonb dignol a 3 basiy noft where V is the blood velocity, u the blood viscosity (FL-2T), p the blood density (ML), D the artery diameter, Ao the area of the unobstructed artery, and A, the area of the stenosis. Determine the dimensions of the constants K, and K. Would this equation be valid in any system of units?l .ll O 92 15:25 moodle.nct.edu.om/mod/ 11 P Flag question Calculate the density, weight density, specific mass of two liters of a fluid of weighs 5 kg (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) density of fluid (unit in kg/m3) : %3D weight density of fluid is (Unit in N/m³) specific mass (unit in m3/kg) = specific gravity = Question 8 Not yet answered
- A dimensionless combination of variables that is important in the study of viscous flow through pipes is called the Reynolds number, Re, defined as ???/? where, as indicated in Fig. 11, ? is the fluid density, V the mean fluid velocity, D the pipe diameter, and the fluid viscosity. A Newtonian fluid having a viscosity of 0.38 ? . ?/?² and a specific gravity of 0.91 flows through a 25‐mmdiameter pipe with a velocity of 2.6 ?/?. Determine the value of the Reynolds number using (a) SI units, and (b) BG units.Assignment 3 On Viscosity Calculation - Word TOUT REFERENCES MAILINGS REVIEW VIEW Hyperlink P Bookmark tArt Chart Screenshot Apps for Office Online Video Cross-reference Comment Header Footer Page Number Text Quick WordA Box Parts - ns Apps Media Links Comments Header & Footer (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). (a) Calculate the shear stress ty and the velocity (b) gradient of shear rate -/dy using cgs units. (c) Repeat using SI units. A Torce Fdshear berween teoparailel platesQus A fluid flow situatton depends the Velocity (V), the on density several lineor dimension, tsh, L2, pressure drop (PP) » gravity (o),Viscosity Ms Susface tension (), and bulk mo dulus of elasticity k. Apply dimen sional analysis. to these variables ed MKEA
- Using II-Theorem method to Express (n) in terms of dimensionless groups.The efficiency (n) of a fan depends upon density (p), and dynamic viscosity (u), of the fluid, angular velocity (@), diameter of the rotator (D), and discharge (Q). Q3/ A petroleum crude oil having a kinematics viscosity 0.0001 m?/s is flowing through the piping arrangement shown in the below Figure,The total mass flow rate is equal 10 kg/s entering in pipe (A) . The flow divides to three pipes ( B, C, D). The steel pipes are schedule 40 pipe. note that the dynamic viscosity 0.088 kg/m.s. Calculate the following using SI units: 1- The type of flow in pipe (A). 2- The mass velocity in pipe (B) GB. 3- The velocity in pipe (D) Up. 4- The Volumetric flow rate in pipe (D) QD. 5- The Volumetric flow rate in pipe (C) Qc. Og = 2o mm Ug = 2UA Perolenm crude oIL A ma = 1o Kg/s O = 5o mm mic = ? Go = 7000 k9/m.s Nate that!- O, = 30 mm. D:0iameter. U:velocity G mass velocity mimass How vateThe Reynold's number of a sphere falling in air is 1E6. If the sphere's radius is 1ft, what is its velocity? Density of air is 0.00234 slug/ft³ and viscosity of air is 3.8E-7 lbf-sec/ft²A. 2.5 ft/sB. 5.1 ft/sC. 40.6 ft/sD. 81.2 ft/sAccording to the Newton's cooling law, the temperature of any substance is directly related to the distinction between the substance temperature and its environment (ambient) temperature dT =-k(T – T,)k(T-T) dt where Tis the substance temperature (C) T is the time (minute) k is constant T. is environmental temperature A casting ladle of molten metal has 290 °C, By using Euler methodology, evaluate the temperature from t=0 to 35 min with a step size of 2 min. If, T, is 25°C and k is 0,009/min.