I need the answer as soon as possible R₁4.7kFig. 2II. Refer to Figure 2.1. State if the circuit below in Figure 2 is a high pass or low pass filter, and calculate a suitable capacitorvalue such that the circuit has a cut-off frequency of 2 kHz.2. The circuit shown in Figure 2 is connected to an ac voltage source of 12 V and frequency 2 kHz.Calculate the magnitude and phase, with reference to the 12 V source, of the current in the circuit, andthe magnitude and phase of the voltage across each component.i)ii)Sketch a phasor diagram indicating the source voltage, voltage across each component, and the circuitcurrent.3. For the circuit shown in Figure 2:i) Using the log-linear graph paper provided at the end of this booklet, sketch a straight-line approximationto the filter's response, i.e. gain in dB versus frequency on a logarithmic scale, and use this to sketch anappropriate curve approximating the filter's response. Use a frequency range from 1 Hz to 1 MHz. Attachthe graph to your answer book.ii) State the frequency at which your straight-line approximation has the greatest error, and the value of thaterror.iii) Explain why the -3dB frequency is sometimes called the 'cut-off frequency'.iv) State the value of the gradient of the sloping portion of your graph.VsC₁Vo

Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

II. Refer to Figure 2. 1. State if the circuit below in Figure 2 is a high pass or low pass filter, and calculate a suitable capacitor value such that the circuit has a cut-off frequency of 2 kHz. 2. i) The circuit shown in Figure 2 is connected to an ac voltage source of 12 V and frequency 2 kHz. Calculate the magnitude and phase, with reference to the 12 V source, of the current in the circuit, and the magnitude and phase of the voltage across each component. ii) Sketch a phasor diagram indicating the source voltage, voltage across each component, and the circuit current.

II. Refer to Figure 2. 1. State if the circuit below in Figure 2 is a high pass or low pass filter, and calculate a suitable capacitor value such that the circuit has a cut-off frequency of 2 kHz. 2. i) The circuit shown in Figure 2 is connected to an ac voltage source of 12 V and frequency 2 kHz. Calculate the magnitude and phase, with reference to the 12 V source, of the current in the circuit, and the magnitude and phase of the voltage across each component. ii) Sketch a phasor diagram indicating the source voltage, voltage across each component, and the circuit current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Look at the photos and answer the questions
Give information regarding the Heading Indicator. >History >Development and Timeline>Application >How it works>Regulations
which ones are the answers??????
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
I have the answers fro my textbook they are not matching with the one that you send
Get the same shape required and Give proper label and title by using OCTAVE and write the program
Why did not I find your solution to all my questions ?
Please answer in typing format
I want to solve both questions please
Grateful some help with this question thanks.