II. Design a reinforced concrete beam to carry a service live load of 10kN/m and dead load of 6kN/m (including its own weight) Use f 'c = 27MPA, fy = 414MPA, b = d/2. The beam is to be reinforced in tension only. L1 = number of letters of your first name L2 = number of letters of your family name Wu L1 L2

II. Design a reinforced concrete beam to carry a service live load of 10kN/m and dead load of 6kN/m (including its own weight) Use f 'c = 27MPA, fy = 414MPA, b = d/2. The beam is to be reinforced in tension only. L1 = number of letters of your first name L2 = number of letters of your family name Wu L1 L2

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

3.4 The required flexural (bending moment) strength is of a reinforced concrete beam is Mu = 260 kip-ft Determine which of the following reinforcing bar arrangements can be used for this beam. a) 6-#6 b) 4-#8 c) 3-#9 Material properties are: f'c = 5 ksi fy = 60 ksi 12" 24" #4 Stirrups 1in cover over the stirrups
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @ FACE OF SUPPORTS TOP BARS 2-∅20 mm 5-∅20 mm BOTTOM BARS 3-∅20 mm 2-∅20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: Tensile steel ratio in positive bending at midspan = __________ (in 5 decimal places) Design Moment strength of section at midspan for positive bending = ___________ kN·m (nearest whole number) Nominal Moment strength of section at face of support for negative bending = ___________ kN·m (nearest whole number)
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f’c = 28 MPa fy = 276 MPa Aps = 800 mm2 Ds = 10 mm Dm = 18 mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250 kN
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @ FACE OF SUPPORTS TOP BARS 2-16 mm diameters 5-16 mm diameters BOTTOM BARS 3-16 mm diameters 2-16 mm diameters Given: Stirrup diameter = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 250 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: Tensile steel ratio in positive bending at midspan Design Moment Strength of section at midspan for positive bending in kN-m Nominal Moment Strength of section at face of support for negative bending in kN-m
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the tensile ratio in positive bending at midspan =
a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the DESIGN moment strength of section at midspan for positive bending
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)