A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 155mm and the wall thickness is 12mm. If the air in the tank is pressurized to 19.7MPA, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: (a) Olong= i MPa MPa Ohoop = (b) Tmax = i MPa (c) Tabs max = i MPа

A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 155mm and the wall thickness is 12mm. If the air in the tank is pressurized to 19.7MPA, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: (a) Olong= i MPa MPa Ohoop = (b) Tmax = i MPa (c) Tabs max = i MPа

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow titanium [G = 46 GPa] shaft has an outside diameter of D = 56 mm and a wall thickness of t = 1.88 mm. The maximum shear stress in the shaft must be limited to 243 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 27 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 75 kW is being transmitted at 9 Hz. Answers: (a) P = i (b) = kW.
A wire of circular cross section is wound around a drum of 500 mm diameter. Ewire 100 GPa. If the normal stress in the wire material is not to exceed 50 MPa, the radius of the wire cross section must be
A steel rod 3 ft long with a cross-sectional area of 0.3 in.² is stretched between two fixed points. The tensile force in the rod is 1300 lb at 40°F. Using a = 6.5 x 10-6 / °F and E = 29 x 106 psi, calculate the temperature at which the stress in the rod will be (a) 10 ksi; and (b) zero.
Stress
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.
1
A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 22 mm. Compute the maximum stress in the bar Use E = 230 GPa. Answer must be in MPa.
An 8-mm thick steel tank has an outside diameter of 600 mm. It is internal pressure of 2.40 MPa. Determine the maximum subjected to stress in the tank. an
A solid steel bar 50 mm in diameter and 1.5 m long is secured between rigid walls. If the stress in the bar is zero at 27°C, what will be the stress (MPa) in the bar when the temperature rises to 42°C? Use E 200 GPa and a = 12.5 x 10-6 m/m-°C.
Two wooden studs with cross-sectional dimensions 45×145 mm2 are glued together to form a beam with a T-sectionaccording to the figure on the right and loaded according to the figure on the left. The beam is loaded in its rigiddirection.a) Calculate the moment of inertia of the cross-section about the centroid axis (z-axis).b) Calculate the maximum normal stress in the beam.c) Sketch the normal stress distribution over the most loaded cross-section of the beam. All calculations must be clear and handwritten, draw and check so that the answers are correct
Q3.For the stress state shown below: 300 MPa 100 MPa 100 MPa → 200 MPa 200 MPa - 100 MPa 100 MPa 300 MPa (a) Plot Mohr's circle for the stress state. (b) Calculate the principal stresses and their orientation with respect to ther axis? (c) Using your answer from (b) to help you, plot Mohr's circle for strain.
The tank shown in the Figure below is fabricated from a 10-mm steel plate. If the internal pressure in the tank is 1.2 MPa, calculate the tangential stress in the tank in MPa? ... 400 mm 600 mm