If the particle which is represented by point A is to be at equilibrium and that FAD= (-550i+ 650) + 450k)N, determine the magnitudes of the other forces (i.e. magnitudes of FAB, FAC and FAE) particle

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: Find the value of a. TO a. Vs +3

A:

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A:

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: 4. In what standard plates can we index the following. Solve using sil label each values. a. gear of…

A: we have to determine the plate size for manufacturing the given items by simple indexing

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: Simple gear train has/have gear/s on each shaft. O two O two or more coaxial gears O two or three O…

A: Question:- Simple gear train has/have ONE gear on each shaft. Two Two or more coaxial gear Two or…

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: Please show the computation in solving for NB and FAB

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: The teeth of the gear arrangement have Gear A = 40 teeth, Gear B = 70 teeth, and Gear C = 50 teeth,…

A: Find  Pitch circle diameter of Gear C.

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: SHAFT KEY

A:

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: A postman begin at the.. He walks vector A = North-West for 530 meters, then vector B = North for…

A: Displacement is defined as the shortest distance of an object from its initial starting position. It…

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: The other degree of rotation from the start point that will result in Erika being the same distance…

A:

Q: A chain and sprocket has a pitch diameter of 30 inches and with 90 teeth available. Find the pitch…

A: Given data, D = 30 in     ( D = Pitch diameter ) T = 90          ( T = no. Of teeth ) Find pitch = P

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: For the following internal dovetail, if bis 40mm greater than c, m is 60mm less than b, h is 25 mm…

A:

Q: If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2

A:

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A: Given Gear train arrangement To find Gear train which will be effective for bearing

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.